Chapter GMW | E30 LS1 (starting on post #1427)
-
And they're off!
First one done! I think this fuel relay one was supposed to be on a relay. I'll figure it out soon enough.
Got a good chunk started. Also have a lot of questions.
Wire 27x on the expansion board harness goes to pin #7 on the monotronic side for the VVT. Still going through the question marks one by one.
@DrLeadFoot
-
Turned my attention to the grounds. I might take a different approach by making a separate grounding block that connects at the common chassis ground. I'm fearful that I might be overloading some pins by attaching more than one ground wire. Thoughts?
I still need to wire the coil drivers so there are 6 more grounds there.
On to the crank signal wires with the shielding. I cut an old cable wire from the ceiling of my basement and cut/pealed the shielding to re-wrap the signal wires after I soldered them.
Not too pretty but I'll wrap it in electrical tape to clean it up and secure it.
I need to get some 18 & 20 gauge wire and solder in my coils. Any input on how to ground all these wires would be great. Thanks for looking!
@DrLeadFoot
-
So happy I bought a full plug-and-play MS2 setup after seeing this.... Yikes.
I feel very overwhelmed at the moment but Snap and Derek (bimmerforums.com member) have been huge helps. It is the unknowns that I have with how the software works that concern me. I also feel like I need to put some resistors somewhere but I haven't looked into that yet.
Nah, just a lot of information checking. He will get it just fine
Your wife has to think you're having an affair with how many times I text you at all hours of the day/night. #jakefromstatefarm
@DrLeadFoot
-
Uhhhhh khakis
-
Home depot sells shielded wire too.
Grounding everything to the same chassis ground is definitely a great idea. I would be less worried about overloading grounds and only slightly more concerned with any noise in the signals due to shared grounds. A handful of the ground pins are the same on the harness (multiple pins with continuity to eachother) so that even isnt much of a concern depending on which components are grounded together.
Any excessive electrical noise for a component will how up in a log file . Youre going to love the diagnostic capability of being able to see what all your sensors are doing
-
Even though they are common grounds, I would run all separates wires to a common point on the engine block for best results. Don't connect multiple grounds before the engine block.
Sent from my iPhone using Tapatalk
Shouldn't I use the grounding point that the ECU uses?
@DrLeadFoot
-
Some wedding shots of the E30
http://jbephotography.zenfolio.com/p927518357/h49c3463b#h49c35677
http://jbephotography.zenfolio.com/p927518357/h49C35677#h49c3559d
@DrLeadFoot
-
That's awesome!
-
-
Haha. Que the music!
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
-
Coils are all wired up. I need to see if I need to run them to grounds coming from the harness or if I can just run them directly to the chassis ground. I'm leaning towards running the grounds to the harness.
I disconnected the grounds from the MS3 and Expansion board from the pins. I'll run these to the chassis ground for sure. I don't want to overload those pins.
I still feel like I'm winging it so please help with any input.
A wired up coil.
From DBurt86's build thread:
http://s314.photobucket.com/user/dburt86/media/coil%20driver_zpssqcdevwu.png.htmlAll sealed up.
@DrLeadFoot
-
This is what they are resting on when in the stock 413 red label ECU. I could use this as the heat sink and bolt it to the cover to dissipate the heat. What do you think?
__________________@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login