Alpine e30 progress/build thread
-
I have a Behr (?) m42 rad in my car currently that I will no longer be in need of if you want to make a linear move on the car.
-
Continued taking stuff apart today after work, Only major thing left is the AC condenser but I can't get the line from the compressor off at either side so I'm going to have to pull both of them at the same time. No big deal though, got the rest of the AC removed and a bunch of other odds and ends. Started planning my cuts as well
Recently I noticed that the passenger side wiper wasn't centered in its hole and was stuck up towards the windshield, the hood probably caught it when it was forced backwards. I pulled the wiper arm and all the cowl grills and stuff, was able to get the wiper arm free but the cowl sheet metal is damaged. Looks like I'm going to have to remove the wiper linkage so I can straighten this out from the back side. It doesn't look bad but the hole is elongated by about 1/4" and pushed down behind it by about that much. Fortunately the linkage seems to be ok. From what I can tell, the only way to remove this is through the opening the blower motor is mounted in? That's going to suck for sure...
Realized I wasn't properly storing the car, so I fixed that as well
-
removing the wiper linkage and motor?
ever try and solve one of these? pretty much the same task.
maybe just add some sort of additional black plastic/rubber washer that is larger and covers the elongated hole instead? i don't like shortcuts, but sometimes personal sanity needs to be a consideration when working on cars
Dan
-
removing the wiper linkage and motor?
ever try and solve one of these? pretty much the same task.
maybe just add some sort of additional black plastic/rubber washer that is larger and covers the elongated hole instead? i don't like shortcuts, but sometimes personal sanity needs to be a consideration when working on cars [emoji3]
Hahaha I figured as much. Normally I would be all for just covering the hole if it meant keeping my sanity, but unfortunately it is also bent downwards (hard to see in the picture, you can see the windshield seal isnt sitting flat) so its pretty much a big dent. Given your analogy, Ill probably save this task for when I pull the engine, since I'd have to remove half of it to get that thing out anyway...
-
The sawzall and angle grinder I was going to borrow to start cutting the front off the car are being used by my dad at the moment so I have been working on some other projects.
My garage is not heated and with temperatures dropping (especially now) I don't have a way to be able to paint parts. Instead of heating my entire garage in order to paint something I decided to make an "oven" that I can use to keep the paint and part warm before spraying and also allow the paint to cure properly. It is a 3'x2'x2' box made of 1" foam board insulation and just held together with a ton of duct tape:
It is big enough that I can fit most things that I will need to paint this winter. There are two incandescent light bulbs to provide the heat, I used "rough" bulbs as they have a thicker filament that emits more heat than a standard bulb of the same wattage (dimmer light output = more heat output). The lights are connected to a control box that I built. It uses a small thermostat commonly found in home brewing setups to flip a relay that switches the lights on and off depending on the internal temperature. The thermostat reads the internal temperature from a thermocouple inside the center of the box. I programmed the thermostat and did some trial runs today and it works very well, it should save me a lot of money compared to heating the whole garage just to paint things. The whole setup cost me less than $60.
I got the rear brakes pulled from the trailing arms and started the rebuild process on the calipers. I received the fronts already disassembled and started breaking down the rears. Got new rotors for the front and the rears look really new so I'm just going to clean them up and run them. Also rebuilt my driver's door lock as it hasn't been working as long as I owned the car.
-
-
that must have been a bit terrifying!
Having never done this before, the first cut was definitely a little scary
-
It's 8 million times easier to do engine things now.....sooooooo you might as well pull it and freshen it up
-
It's 8 million times easier to do engine things now.....sooooooo you might as well pull it and freshen it up
lots of elbow room for fitting FI piping too
Dan
-
Even easier thing would be to set the front subframe and trans brace on stands/blocks, unbolt them both, then lift up the front of the car by hand (it's light enough) and push it backwards like a wheel barrow
Light enough? Jesus earl. You on a diet of spinach only?
-
Earl is the Incredible Hulk. Spot him and he'll left your house.
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login