'88 E30
-
Do you know the spring rates?
I probably won't need the brake stuff as I've already ordered brakes/calipers
-
well it happened, ordered about $1650 worth of crap tonight for it. (will get about $160 back in core)
Still remaining to buy:
coil overs
brake pads & fluid (still on the fence about pads)
front stainless brake lines
That's some serious cash coming from the guy who didn't want to buy a radiator fan relay.
Keep up the good work!! -
Brake supplies are in! Just need to get some front stainless lines and pads/fluid
-
wheel bearings/lock rings, rack boots/clamps, rear sway bar mount reinforcements came today
getting closer
-
Got the new wheel bearings and hubs pressed into the trailing arms today.
Only things I'm waiting on is the skid plate & tierods (and the crap I haven't ordered yet)
Gonna hopefully convince myself to work on it tomorrow
-
This was more of a pain in the ass than I'd like to admit, especially by myself
Butttttt the rear sway bar is in. ST 19mm. Can't imagine doing that with all the subframe crap in the way
-
-
Rest of the parts have arrived.
24v skid plate from red46
Inner and outer e36 tierods
Driveshaft nuts
Spring pads
Still need to order
Suspension (coils?)
Brake pads
Front brake lines
And probably some misc stuff
-
sway bars suck third-ed and move to strike.
glad you got a skid plate, they are 100% necessary for these swaps.
Dan
-
Only thing I'm nervous about is I have an aftermarket core support (my original one was kinda twisted and rusty) the aftermarket China ones work well enough, they are just quite thin and bendy. I think it should work because the red46 plate includes some hardware (drilling required) which includes a plate to sandwich the core support. Should be fine unless I go bounce off some rocks out in moab
-
Only thing I'm nervous about is I have an aftermarket core support (my original one was kinda twisted and rusty) the aftermarket China ones work well enough, they are just quite thin and bendy. I think it should work because the red46 plate includes some hardware (drilling required) which includes a plate to sandwich the core support. Should be fine unless I go bounce off some rocks out in moab
You could always cut the core support open and stick a piece of square tube in there.Â
Wait, e30's aren't supposed to go to Moab? I better cancel my trip..... -
KaiserRolls said:
Only thing I'm nervous about is I have an aftermarket core support (my original one was kinda twisted and rusty) the aftermarket China ones work well enough, they are just quite thin and bendy. I think it should work because the red46 plate includes some hardware (drilling required) which includes a plate to sandwich the core support. Should be fine unless I go bounce off some rocks out in moab
You could always cut the core support open and stick a piece of square tube in there.Â
Wait, e30's aren't supposed to go to Moab? I better cancel my trip.....
We will see if the square tube is needed. For my uses, I doubt it - other end attaches to steering rack bolts. I guess if I hit something hard enough I'd rather tweak the core support vs the subframe/steering rack components
-
you could copy/get the hoop from the 'severe duty skid plates' from the guy on e30tech. i hit some big shit and no frame/steering rack damage with it.
Dan
-
I'm not going crazy low or anything. This is just more of a precaution. The red46 plates are surprisingly beefy
-
Steering rack back together with new lemforder shizzzz. Got the "alignment" (outer length) as close as I could. But my first stop is going to be to the alignment rack
-
Got tired and went inside. This is all the farther I made it. Bought new axle nuts. Promptly lost new axle nuts. Going to re use the old ones because there's nothing wrong with them, stupid shit like that frustrates me
"Hey my new parts showed up" "hey I already misplaced them" they didn't even make it out of the bag they were shipped in
I hate my brain sometimes
-
Oh I also broke the cv boot clamp, so I'll need a new one of those as well
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login