BMW Bushing Puller Tool Needed
-
Hey Ben. I too am too doing rear subframe bushings this winter on my e30 and would be more than willing to lend a hand. I am located in bayview. The car looks great by the way.
-
What a welcome! You guys are more than welcome to come over and make fun of me while I break my car
I'll PM you both once I figure out timing of stuff, but about a week sounds right. I've got two young kids that dictate when I work on the thing. FWIW, I'm going to try to do the bushings without dropping the subframe, per the thread I posted above. Even if you guys are planning on dropping your subframe, the tool should work the same either way.
-
I'm going to try to do the bushings without dropping the subframe, per the thread I posted above.
Are we going to be doing it in 5 minutes too? and please let us know!
BMWCCA #499464
Current - 1995 540i/6 V 2.0 | Dead - 1995 540i/6 | Sold - 1995 318is
-
Are we going to be doing it in 5 minutes too? and please let us know!
I'm shooting for 4. I'll know more about my plans once I find the source of some other noises (hopefully tonight).
-
An air chisel works really well for removing the outer metal sleeve too. Both of you are upgrading to poly bushings I would assume? They last forever so I see no reason to use OEM=) Also, they are easier to install and they stiffen up the rear a nice amount. I put poly in my compact and my e34 has all poly rear bushings and it feels excellent.
-
An air chisel works really well for removing the outer metal sleeve too. Both of you are upgrading to poly bushings I would assume? They last forever so I see no reason to use OEM=) Also, they are easier to install and they stiffen up the rear a nice amount. I put poly in my compact and my e34 has all poly rear bushings and it feels excellent.
Aren't poly's pretty noisy / harsh?
-
I'm shooting for 4. I'll know more about my plans once I find the source of some other noises (hopefully tonight).
I don't know what you were thinking but how would next Monday afternoon work for messing around with some bushings?
BMWCCA #499464
Current - 1995 540i/6 V 2.0 | Dead - 1995 540i/6 | Sold - 1995 318is
-
I'm just throwing this out there but if you wanted to or would be able to we could do my bushings Monday evening. I have the bushings in my trunk I just don't have a place to do them in Milwaukee. Just an idea
BMWCCA #499464
Current - 1995 540i/6 V 2.0 | Dead - 1995 540i/6 | Sold - 1995 318is
-
Did you get this done? I might be able to do them on a hydraulic press for you.
-
Just to update the thread. I finally carved out some time, and replaced the bushings without removing subframe or the bolts using the techinques in the link I posted earlier.
I didn't take any pics of the process, but it was very straight forward. The only think I'll add to the above is that if you need to replace the plate washers that sit on top of the bushings, you might have to remove the subframe bolts to install them.
So, I've now got a homemade bushing puller thing that I'll happily loan out to whoever for the cost of shipping. It took me about an hour to make the tool, but I was trying to be carefull to get as good a fit as reasonable without going totally anal-rententive.
I'll start a new thread about how I'd like the loaning process to go, and what other tools you'll need to do the job.
-
It might... My guess it would depend if the bushing is seized onto the bolt / frame of the car. Then again, if it's not a vert, you could probably remove the bolts and then get a saw in there to remove whatever the tool didn't remove.
It's worth a shot... worst case, you'd just pull the subframe anyway.
But... If your subframe bushings are that bad, your trailing arm bushings are probably shot too. You'd probably save time by removing the subframe and doing both jobs at once.
-
Well borrowed Ben's tool, and no success for me. Puller and heat and all I accomplished was bending the outer metal lip of the subframe bushing. Short of pulling the subframe which I really don't have time or the inclination to do, any suggestions on options? I was able to knock out the long bolt. Thanks.
-
Thanks. I used a drill and hole saw to clear most of the rubber. Metal center though looks to be stuck to the body. The outer sleeve is stuck to the subframe tube. Car is on jack stands so not enough height to use the sawzall. Any other suggestions ? Starting to see why folks drop the subframe to do this.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login