chit chat thread
-
...drilling aluminum should be easy for every machine.
I don't know about that one. If I put a dial indicator on router and push on it with my finger, it only takes a couple pounds of force to get .010" of deflection. The deflection causes the angle and position of the spindle to change relative to the table, which puts a lot of bad mojo into a drill bit that's spinning 15-30k rpm. A big part of the problem is the plastic mounting bracket for the spindle, but there is still a fair amount of deflection in the frame itself. It's a router table, not a vertical machining center.
http://www.probotix.com/COMET-CNC-ROUTER
However, my fear of the twisty frame and bogging router rpms has caused me to lower my feed rates too much. On the last cut the bit was getting gummed up, presumably because the chips are getting melty. Speeding the feed back up actually made it cut better. When I get some free time, I'll put another piece of aluminum on there and let'er eat, but I'm fairly sure it will just snap the bit.
-
I have had drill bits deflect about 3degrees without breaking (when drilling into an angle with no spot drill) tooling makes a difference. As for milling with a router table what I had found useful in routers and milling centers is setting up an air blast that point directly on the milling or drill bit to clear the chips. When machining on unstable work pieces or machines of will greatly benefit the job. Worst thing for tool life is double cutting chips and starts to bind in the flutes ( melty chips). Since you can't use a flood coolant on your router use air. A air gun from a compressor would work if you wanted to hold it. Also get coated end mills the will help tremendously with chips not clogging the flutes up.
1976 530i e12
1990 325ix e30
1992 325i e36
1995 740il e38
2001 330xi e46
^More to come
-
http://bringatrailer.com/listing/1970-bmw-m2-1600-2-with-s14-m3-engine/
I'm guessing it goes for $75,000
-
http://bringatrailer.com/listing/1970-bmw-m2-1600-2-with-s14-m3-engine/
I'm guessing it goes for $75,000
That looks so good
-
My wife showed me this today. Not sure who actually has a Facebook thing
https://m.facebook.com/SKYLINESthelimit/posts/683884955155750
Hey I know that guy
-
Jeff said:
My wife showed me this today. Not sure who actually has a Facebook thing https://m.facebook.com/SKYLINESthelimit/posts/683884955155750
Hey I know that guy
Interesting, where did you meet him?
1976 530i e12
1990 325ix e30
1992 325i e36
1995 740il e38
2001 330xi e46
^More to come -
Hey I know that guy
I wonder how I never saw that. That was funny as hell!..
Picked these up for the e38 this weekend
How much did you pay if you dont mind me asking?
-
KaiserRolls said:
Jeff said:
My wife showed me this today. Not sure who actually has a Facebook thing https://m.facebook.com/SKYLINESthelimit/posts/683884955155750
Hey I know that guy
Interesting, where did you meet him?
I've known him for 25 years
-
^^ -
Finally took some pictures of the test fixture that I built for work. Too bad my phone was being a potato.
It's for testing a 6-up array of LED lighting boards. It's a basic functional test; just put 12v on it and make sure it lights up. Previously we were manually sticking meter leads in the connector on each board while holding a welding face mask over it so you didn't get blinded. This should be an improvement.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login