'88 E30
-
Snap said:
I have always done them under the axle nut like shown in the picture.
As you tighten the axle nut the lock plate crushes down and prevents the corners of the axle nut from rotating past them until you pry them open
you are smoking crack that picture clearly shows the lock plate on top of the nut. how does a flat plate crush down? the back of the axle nut is round, not hex.
KaiserRolls said:
I will gladly beat the shit out of them from pure frustration tonight
Makes sense to put them on after to bend them to the shape of the hex though
you shouldnt be torquing your axle nuts down without the subframe installed and the weight of the car on the wheels/hub IIRC. i don't know if it would even be possible, they get torqued to 180ft/lbs or something, you will have to hold the axle somehow...
I will fight this one to the death. it may have been 4 years ago but im pretty sure you Ben and Mitch are Bushelmasters
-
Kaiser Rules Andy Drools
-
Good thing I have deep sockets, a big hammer and the right mental attitude regarding lock plates
-
Fuck this. I'm throwing them away. Just gonna tighten the shit out of it
Lolololol
-
ignore brian, he's on crack like i mentioned before.
since when is real oem an accurate assembly guide? i suppose brian must have two stacked 5-lug front rotors on your e30 as shown in this diagram:
Dan
-
since when is real oem an accurate assembly guide? i suppose brian must have two stacked 5-lug front rotors on your e30 as shown in this diagram:
oof. checkmate.
-
Rofl @ rotors on top of rotors
but it I mean I definitely agree with the strategy of using a hammer. I'm not sure a project is actually a project without using one.
2011 E92 M3 6MT ZCP - ESS 625 supercharged
2007 Z4MR
2003 E39 M5
2002 E46 M3
2021 X5 40i -
Found my axle nuts. In a box. Labeled. "Sway bar parts" guys I think I need to quit at things
-
Brian, my tuning pitchfork is currently resting in the garage.
I shall brandish my axle nut shovel for this discussion.You are an engineer, and it saddens me that you are subscribing to the theory of the lock plate being used as a washer to ensure the nut doesn't rotate. In your assemblies do you not use lock nuts when you are doing sheet metal? Because the sheet metal would deform and capture the nut, in your theory.Though that depends on the type of metal used.
I could easily remove an axle nut with the lock plate behind it. But if you put it on the proper way (over the nut) you cannot even get a socket on it. That bad boy is locked in there.
#endrant
-
FWIW: mine were put on incorrectly by the PO. ("Washers" behind nut) I spun them off with an impact, bent tabs and all
-
Shots fired!
-
To end this all check out my snap chat tech tips. Bring your own beer
Kaiser_rolls
-
It's all put back together. Everything is torqued besides the axle nutzz
-
You guys are correct. My memory sucks and I suck.
Back to my mound of cocaine....
It's okay sir. I shall now retire my shovel for further axle nut discussions.
Seriously, whoever doesn't have Mr. Kaiser on snapchat is/was missing out. His series of "tech tips" was causing me to have uncontrollable laughter last night.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login