Chapter GMW | E30 LS1 (starting on post #1427)
-
Sorting out a couple more ground wires then I should be all done with the dme side of the wiring harness. Still need to wire up the new gauges and the GM IAT sensor.Heat Sink'd the coil drivers.
Where I left it. 
Sent from my SM-G900V using TapatalkAre those puzzle pieces on your socks!?!?!
Hipsters.......sigh.....
-
Sorting out a couple more ground wires then I should be all done with the dme side of the wiring harness. Still need to wire up the new gauges and the GM IAT sensor.Heat Sink'd the coil drivers.Where I left it. Sent from my SM-G900V using Tapatalk
Are those puzzle pieces on your socks!?!?!
Hipsters.......sigh.....
That's my signature Realtor "look". You wanna buy a house??!
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Glad you are doing a careful/quality job on the wiring. it looks good and will pay off
I sure hope so!
@DrLeadFoot
-
Going to make the temp sensor into a vacuum port or find a barb fitting at the hardware store.
Took a straight edge and a feeler gauge to the block at a bunch of different angles. This is the only spot that the .0015" feeler gauge found a gap. It has resistance but it still goes under the straight edge. The area in question is by the coolant port and is a little wider than the gauge. Thoughts?
@DrLeadFoot
-
Ben has something similar going on with his block as well.
I dont have the specs for a BMW handy but I believe .002" is the max. deviation for flatness on a typical cylinder head.
I wouldn't let it bother me if I were you. Nobody can say for sure that it will be fine/be a problem but if I were in your shoes i'd just forget about it and run with it.
-
That is kind of odd, it looks a lot like the imperfection that I have in mine!
With the material the HG is made out of I think it should be fine.
That doesn't extend to the cylinder does it? If not I wouldn't be too concerned about it. -
That is kind of odd, it looks a lot like the imperfection that I have in mine!
With the material the HG is made out of I think it should be fine.
That doesn't extend to the cylinder does it? If not I wouldn't be too concerned about it.
It does touch the cylinder wall. Honda Bond and call it a day?
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Wiring up the traction control. Any pointers on which front ABS wire to tap into?
For the rear I'll use the vehicle speed sensor.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Posting this here for traction control reference. Any tips? Running MS3X
@DrLeadFoot
-
Where have I heard that name before?
From what ive researched, if you tap into an existing + from an ABS sensor then you need to amplify the signal like you mentioned the other day. Dialing in the amplification on that link I texted you looks like it requires an oscilloscope and an electrical engineering degree which is why I suggested making a bracket to mount a standalone wheel speed sensor.
-
Where have I heard that name before? From what ive researched, if you tap into an existing + from an ABS sensor then you need to amplify the signal like you mentioned the other day. Dialing in the amplification on that link I texted you looks like it requires an oscilloscope and an electrical engineering degree which is why I suggested making a bracket to mount a standalone wheel speed sensor.
he is a BF.C frequent user that has helped answer a few of my questions and knows his stuff.
I remember he used some signal converter that was cheap and got it to work great. Just facebook him or get him on BF.C. He will answer your question without any head scratching.
sk8 or die
-
Where have I heard that name before? From what ive researched, if you tap into an existing + from an ABS sensor then you need to amplify the signal like you mentioned the other day. Dialing in the amplification on that link I texted you looks like it requires an oscilloscope and an electrical engineering degree which is why I suggested making a bracket to mount a standalone wheel speed sensor.
he is a BF.C frequent user that has helped answer a few of my questions and knows his stuff.
I remember he used some signal converter that was cheap and got it to work great. Just facebook him or get him on BF.C. He will answer your question without any head scratching.
Derek and Snap have been huge helps
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
I have the traction control under control in my head after a bunch of texts, a phone call and a little research on my end.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Intake Air Temp thread reference. Going to order a barbed vacuum fitting.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
The one on the underside of the manifold?
Wiring for traction control looks about right, though I have not used one of the conditioners. What one did you end up using?
Edit: Just kidding, went back a page and found it. -
The one on the underside of the manifold?
Wiring for traction control looks about right, though I have not used one of the conditioners. What one did you end up using?
Edit: Just kidding, went back a page and found it.
The one under the manifold. I'll order this today. http://www.ebay.com/itm/like/161772492725?ul_noapp=true&chn=ps&lpid=82
I went to David Hobbs Honda yesterday. He didn't put me in a honda but I gave him money and he gave me hondabond.
@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login