M20 Turbo => M50 turbo fun.
-
Snap Understeer said:
Rustowleyum, Hi.
Dont go lean.
That is all.
bye!!! 1
Kashi takes like recycled cardboard.
-
Rowleym said:
Why wouldn't I? I don't need to lower the compression at all.
m50 headgaskets are notorious for blowing without boost at all.
-
Rowleym said:
I'm looking for 350-400wheel, and this motor normally support 350 without arp's even. I think I should be able to manage. If I blow it, oh well. It's like a boost fuse haha. Too much boost and bad tuning, I blow a hg versus a piston haha.
ha! I like that.
Better than blowing the welds on your intake manifold for sure!!!!!!!!!!!!
p.s. !!!!!!!!!!!!!!
-
Rowleym said:
I'm looking for 350-400wheel, and this motor normally support 350 without arp's even. I think I should be able to manage. If I blow it, oh well. It's like a boost fuse haha. Too much boost and bad tuning, I blow a hg versus a piston haha.
It's common practice in the turbo volvo world to run a factory head gasket and treat it like a fuse. Those who go the MLS Cometic approach (without a lot of time spent tuning on the dyno by a professional) often live to regret that decision.
-
Rowleym said:
Alright for sure. Would you just run rubber lines? Like those high pressure efi ones? Or would you do braided? Also, do you think i need a new fuel rail? This fuel thing is really getting me.
Go braided. Looks better. And the fuel rail, factory fuel rail *should* be fine. Just upgrade injectors/possibly get a higher bar FPR.
-
The Full Banana said:
It's common practice in the turbo volvo world to run a factory head gasket and treat it like a fuse. Those who go the MLS Cometic approach (without a lot of time spent tuning on the dyno by a professional) often live to regret that decision.
Maybe, I went Cometic to get a lower CR.
-
The kool-aid man prefers Cometic gaskets 9 times out of 10.
-
Snap Understeer said:
You seem to be the expert on this subject so I have a question for you. Can the kool-aid man bust through a wall made of Cometic gaskets?
OH YEAAAAAAAAAAAAH
To clarify: There is nothing wrong with cometic gaskets at all. They are great, but for a lot of people, they just aren't necessarily the best choice.
-
Why would they not be the best decision?
People not understanding that a motor can only take so much boost?
Sent from the future. Or my phone, who knows.
-
Yea but its kind of cheating when using a Mls to lower compression. A lot of the time people run them and think they can turn the boost up real high, and then they end up blowing it up because they don't have a proper tune. Proper tune and you are good to go! It's a great way to use pump gas. I'm quite stoked about this e85 thing. Absolutely no need for me to lower compression
sk8 or die
-
Brian said:
Go braided. Looks better. And the fuel rail, factory fuel rail *should* be fine. Just upgrade injectors/possibly get a higher bar FPR.
It doesn't matter to me if it looks good, I was just wondering if the rubber stuff performs as well. The 80# injectors will already be more than enough, I just need the rest of the fuel system to handle it!
sk8 or die
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login