The E46 M3 Journal
-
Im guessing you had a jumper pack on it? Hate to ask the obvious questions but hows the battery voltage?
My voltage meter is in my e30 trunk which has the whole e46 front end on top of it.
The battery is about 1 year old and is an OEM bmw unit. It should hold a charge once fully charged up. Do that first and reassess. If that doesn't work, replace the starter with the original one. The one in the car now is a non-bmw re-man unit.
Also need to look into properly getting the smg unit bled. The pump makes noise but doesn't go into gear.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
The car is in "0" but maybe the clutch isn't disengaged.
The car should start with the hood open but you can't shift it into gear.
I have 12.4 volts at the battery in the trunk and started.
I jumped the starter with a screw driver and it works.
I feel it's the key not talking to the car. There is a name for the system but it escapes me. I'll also make sure my slave shaft is sitting on the fork.
I might be able to get a house call for bleeding the system as a mechanic owes me a favor.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Got some new bolts for the v-brace, oil cooler line engine mount and new o-rings for the oil cooler.
Most importantly got a new key. Hopefully this will start the car.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
SMG isn't "talking" the the starter.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Maybe if the starter would apologize for what he did then the SMG would talk to him again... if only the starter knew what he did wrong.
-
Maybe if the starter would apologize for what he did then the SMG would talk to him again... if only the starter knew what he did wrong.
Replace "starter" with "husband" and "SMG" with "wife"........
-
My issue:
The trans is physically in neutral and still in 0.
- Brand new key from BMW.
- 12.4 volts on the battery.
- The starter works fine and turns the engine over after testing it.
- Replaced the salmon relay with one I know was working.
- No blown fuses, #14 & #30 are good and tested good.
- Hydraulic fluid is filled topped off in the reservoir.
- Hood is closed.
- SMG shifter unit tested and is sending a signal. (Flashes 0 and doesn't go into 1 or R)
- New clutch installed.
- New transmission shift springs.The car won't start or shift out of 0 into 1 or reverse. Yellow SMG light is on and it just flashes 0.
A BMW tech came over and hooked up the computer and there is something not talking to the starter telling it to start. Should I have him reset the system? Bleed it? Bad slave cylinder? I think the SMG system might have been upside down and leaked some fluid from the reservoir hole.
There was water in my SMG circular connector but I cleaned it out and sprayed electrical connector cleaner all over it and blew it out with an air hose.
Please help!!!
@DrLeadFoot
-
Does the trunk have to be closed to start it?
@DrLeadFoot
-
Close the trunk to try lol
All these demands!!!!!
@DrLeadFoot
-
It does not start with the trunk closed.
The SMG pump primes just fine when the car is unlocked.
@DrLeadFoot
-
-
foot on the brake? satanic chant completed?
Did that to no avail.
I feel the smg is preventing the car from starting.
Trying to download DIS_v57 now through a torrent file.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
A friend let me borrow his computer with the DIS and INPA software. The labtop turns itself into a virtual machine but it won't connect to my car.
The ignition is on but it won't read.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Thing won't shift into gear. Flashes 0. Not sure what's up. I know if measures the psi on the slave to make sure the clutch is disengaged.
Hood is closed. Hood latch sensors plugged in. Ugh!!
Matt from Urban Motorworx came over. They key chip is talking to the computer. Getting a failure to start.
The shifter is outputting a signal. Switched the smg relay from the old motor that I know works.
Fuses 14 & 30 tested good.
SMG fluid is topped off.
I cleaned off the smg harness connector. With electrical cleaner. It had water in the connector and protective cover.
Oil level sensor?
I think the smg needs to be bled because it isn't shifting into gear when the key is on.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login