The E46 M3 Journal
-
Surprised its allowed to rotate that much at only twenny nooton meeders
Didn't even know this was a thing. I thought it was screwed up.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Swapped over the intake cam sensor. This one is a slight pain. Need to take off the vacuum tube and fuel rail/injectors.
Turned my attention to the TPS sensors. Took the definitely working ones from the old motor and put them on the new motor. Then swapped all the parts I took off the new motor back to the old one so it can remain complete as possible.
Ordered a couple of transmission gaskets that will get here Wednesday. Also need to swap over all the pulleys and tensioners because they were recently replaced on the original motor. Rear main seal to do still.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Swapped all the idler pulleys and the Rouge Engineering under drive pulleys to the new motor.
Getting there!
Happy new year!
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Slowly chipping away on getting the M3 motor back in. Rear main, gear selector, and transmission input shaft seals all done.
We all know the drill. Pop a hole.
Screw it in.
Needed a bigger screw. And slide hammer it out.
Rear main and pilot bearing all snugged up.
Old shift selector seal.
New one installed.
Transmission input seal.
Next to do is the throw out bearing and clutch fork pivot plastic thing. Pop on the flywheel/clutch/pressure plate. Then mate up the motor and trans. After that it's SMG time!!
@DrLeadFoot
-
How much of a bear is it to pull the selector shaft seal out without scratching the bore? SOP with e30 guys is usually to embed the old seal further into the trans by hammering it in with a 12mm-ish socket and then put the new one in without the risk of gouging the seal bore.
Boom, double seal
-
How much of a bear is it to pull the selector shaft seal out without scratching the bore? SOP with e30 guys is usually to embed the old seal further into the trans by hammering it in with a 12mm-ish socket and then put the new one in without the risk of gouging the seal bore.
Boom, double seal
It wasn't too hard. Just took my time and didn't apply too much pressure.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Not too m3 related but got a winter wheel setup. The m3 is displayed in its current status.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Picked those up from Kerry?
I did! I'm really digging them on the 325xi
@DrLeadFoot
-
Flywheel time!
Took a scotch bright pad and lightly went over the surface.
Torqued down the new bolts to 105NM.
One car garage problems...
Picking up new exhaust manifold gaskets and nuts from BMW today. Not too much to do after I swap over the headers.
Install to-do:
- Headers
- O2 Sensors
- Swap passenger side motor mount arm
- Loosely bolt up motor mounts
- Pressure plate
- Clutch fork, pivot pin, throw-out bearing
- Bolt on Trans to torque spec
- Bolt on SMG systemBundle up and install motor. Outside. In a Wisconsin winter.
@DrLeadFoot
-
Header time!
Took off the headers and labeled both sides of the O2 sensors on both motors with different color zipties.
The old one is on the stand. New one on the ground.
What I'm dealing with for a work space.
@DrLeadFoot
-
You'll be happy to know that denting headers has little to no affect on losing power=)
Someone watches engine masters
-
Judging by that dent, you had some header clearance issues, huh?
That dent is scientifically designed via heat and a BFH to clear the control arm lollipop.
The dent and the grinded down motor mount are due to Kummrow over tightening the motor mount arm (when they reinstalled my headers they took off the motor mount while scratching off a lot of the ceramic coating from trying to jam them in there. Their fix for the ceramic coating was black spray paint.) to block bolts, having them loosen up leading to the breaking of the aluminum motor mount arm and the motor sitting on the steering rack. I couldn't tell it was broken while in the car so I grinded down the arm to make it fit unknowingly doing unnecessary work. Ugh.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
You'll be happy to know that denting headers has little to no affect on losing power=)
Is this true??
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Earl said:
You'll be happy to know that denting headers has little to no affect on losing power=)
Is this true??
Sent from my SM-G900V using Tapatalk
Watch the show engine masters on YouTube
They did it on a Chevy big block v8
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login