TehRaydarlover's AWD lover
-
It was more like 7:15. I couldn't give it to the full potential due to the beans being cold.
Sent from my SCH-I535 using Tapatalk
Hit the sirens
-
Me waking up this morning
Expectation:
Reality:
The neighbors probably wouldn't agree with me that being woken by the god of hellfire would have been more enjoyable that the samsung song of death that is my alarm.
-
hmm for some reason I was under the assumption that s52 rods were forged? Wanted to use them because they are the lightest/strongest(?) 135mm stock rods. I guess some forged h-beams or something wouldn't hurt, just money. With the s52 crank you need custom pistons.
Yeah I was planning on doing the DIYPNP. I just need to do the research on what I want to include as far as extras and how to do it. Then maybe get a little help from someone with the setup and building of it haha.
-
I'm running K1 rods.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
hmm for some reason I was under the assumption that s52 rods were forged? Wanted to use them because they are the lightest/strongest(?) 135mm stock rods. I guess some forged h-beams or something wouldn't hurt, just money. With the s52 crank you need custom pistons.
Yeah I was planning on doing the DIYPNP. I just need to do the research on what I want to include as far as extras and how to do it. Then maybe get a little help from someone with the setup and building of it haha.
s52 rods are one of the best to use! yes!
But because of the custom pistons which of course you need, I was saying why not just do the whole shebang? Not much more expensive at that level.
I actually take that back. If you are running this kind of build, why not go all out and do MS3x? Not much more expensive and I believe its worth it. You can do coil on plug then(with cam sync) and also fully sequential fuel. And tons of other goodies! If you need guidance on what to buy for megasquirt, let me know.
sk8 or die
-
Bit of an update, I noticed that both of my drivers side front cv boots were torn so I decided it was time to swap in the axles I rebuild a while ago. One thing kinda led to another and I ended up replacing a lot of parts.
Got every thing pulled apart. Out with the old and in with the new
Took me two long days to get everything disassembled... break time, off to Europe
5 days in Paris, France
4 day in Luzern, Switzerland
Saw my first touring and it was an ix :') thing was unbelievable must have just been restored. You could perform surgery on the underside of this thing. I tried knocking on the door but no one was home
3 days in Salzburg, Austria
Then finally 3 days in Munich, Germany
Picked up some euro goodies at a junkyard in Munich
THEN THE BMW WELT AND MUSEUM!!!
Another 325ix touring!!
neat
Cleanest m20 ever
Z1
2002
-
The ///M division, I was the first person in the museum because I had to catch my plane to go home, not sure if you are suppose to go up on the platform the cars are on but no one was around so I did haha.
Flying over Greenland
Enough fun back to Minnesota
Cleaning my smileys
Got everything ready to be put back together when I noticed a bit of a problem. Broken subframe bolt
Funny I didn't even notice it broke until I came back from vacation and was ready to put it all back together. The bolt stayed in the subframe when it came down.
I bought an extractor and tried to get the broken subframe bolt out but nothing would work. Soaked it in penetrating oil for 3 days, tried heating it with a torch, nothing... ended up drilling it out and retapping the hole. Put the subframe back on and the new bolt fit perfectly! Thank God! Such a relief seeing I had to drill it out with a hand drill.
Got the new smileys installed and the city lights all wired up after dealing with finding a break in the passengers side wiring.
Got the new front driveshaft all welded and painted
So after all the work I now have rebuilt front axles, new control arms with m3 offset bushings, motor mounts, power steering rack, pump, and reservoir, upper strut mounts, all new belts, euro smileys, German check panel, and new fluids in the front/rear diffs transmission, and transfer case. I also tracked down the broken wire for my oil level sensor so now I have no lights on the dash or check panel! yay
As a reward for all the work I went to a car show and found a 1957 Isetta! So cool!
-
-
-
I think I might order a revshift poly subframe, diff, and trailing arm bushing kit this weekend, 80a hardness... thoughts? I wonder if they could make me a transfer case bushing...
-
Power washed my engine bay and fried some relays
been having some weird random rough idle and no start issues. Swapped in some spare e28 relays and it fixed the no start but I still get the occasional rough idle when I first start the car... -
Damn! Good call! Went out and started it and when it started to stumble, I unplugged the TPS and it immediately shot back up to 900rmp. Can the TPS be adjusted or does it just need to be replaced? I do have a spare if needed.
-
Pulled the tb off but one of the mounting screws for the tps is stripped. Kinda annoying.
-
Installed the spare TPS and it still doesn't want to idle correctly.
when I unplug the TPS the rpms jump up to 900 where it should be. With it plugged in they are at around 6-700... makes me sad.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login