E46 Things
-
Nice job!
-
Keep an eye on that POR-15. I’m sure it’ll be fine but POR usually doesn’t like to adhere to smooth unprotected metal (unless you got the primer/jazz for bare stuff)
Vinyl crunch wrap supreme looks better than silver
-
Keep an eye on that POR-15. I’m sure it’ll be fine but POR usually doesn’t like to adhere to smooth unprotected metal (unless you got the primer/jazz for bare stuff)
Vinyl crunch wrap supreme looks better than silver
I know what you are talking about. I have had it peel off as a nice single chunk before. I used the acid etch. I have never had an issue when I have used the etching-fluid or whatever one would call it.
I have never had a crunch wrap but that sounds so good right now
-
iz that carbon fiber
Just a wrap.
Finished the dash trim. The door armrests are going to be a challenge. I had enough trouble with the minimal curves on the dash trim
-
Use heat and quality vinyl for the arm rests
we did the roof on the evo and it has some really weird/sharp bends by the drip moldings. Just takes some heat and patience
-
Also use knifless tape if you have some edges that are giving you issues. Makes wrapping even easier
-
Upon further review I decided to apply a second layer of orange film to the lights since in some light settings they looked too yellow.
I like to experiment and feel like the cold shift quality could be improved so I am trying out some Redline D4 ATF.
and after checking @gilber33 ‘s build thread I noticed some ramps that would be very helpful for using the jack points so I picked them up for $38 off Amazon.
I broke the cardinal rule of oil changes by not loosening the fill plug before the drain plug and then struggled for some hours to get the fill plug off. This happened because the E46 M3/E39 M5 fill and drain plugs (according to many internet posts sharing similar tragedies) require a hell of a lot of torque to remove. I had the wrench slip and get the ball rolling down the path of roundness.
I estimate about 120 ft-lb of torque to remove the bolt.
I tried many methods but the Sears Damaged Bolt extractor kit was the saving grace.
Buy a set while you still can. This tool has saved me on so many occasions.
It took many hours to get it to perform for me because there is barely any hammer space so a mini sledge driving it on at a 45 degree angle is as good as I could get.
The right combination of luck and cursing helped too. So glad to have that behind me now.
-
A friend of mine uses those little wedge ramps for his car, and they appear to be very convenient!
I have had great success with the rounded head extractor set, though I should really update mine and get the set that goes up to the large sizes!
How are the cold shifts now?
-
I noticed that the Menards by me is selling Craftsman tool boxes. It would be nice if they started selling Craftsman instead of their masterforce junk.
The more likely scenario is that someone will buy the name and the quality will slide down until it's the same as everything else. Not that Craftsman is amazing. Husky is in the same leauge, but doesn't have a lot of the specialty/automotive stuff.
But I digress.
-
I have ramps that I never use. Mostly because my civic doesnt fit on any of them.
Those extractors are awesome. I have a brand new set that I bought just in case, and I always forget I have them. Thanks for the reminder!
The amber looks great on the black.
Let us know how the cold shifts feel!
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
I noticed that the Menards by me is selling Craftsman tool boxes. It would be nice if they started selling Craftsman instead of their masterforce junk.
The more likely scenario is that someone will buy the name and the quality will slide down until it's the same as everything else. Not that Craftsman is amazing. Husky is in the same leauge, but doesn't have a lot of the specialty/automotive stuff.
But I digress.
Craftsman has been owned by Stanley Black & Decker for a few years now. Sears sold off the brand long before the store closings. The Irwin extractor sockets are the same as what Snap-On sells, I know farm and fleet has those in stock.
-
New fill plug came in the mail today so I was able to get it all buttoned back together.
The shifting is improved MUCH more than I had ever hoped for! The oil that was in it was clean and newer but maybe was on the thicker side. The Redline D4 ATF shifts cold like the other oil felt when it was hot. This is how it is supposed to be and I hope the shift quality doesnt degrade in 1000 miles. Im fine changing it every 10k though if I have to.
The clutch delay valve removal and changing the trans oil have made the biggest difference in driving enjoyment and getting the clutch and shifter feel where they should be
-
This update feels like something you might read on priuschat.com or F30post.com:
I figured out how to connect my phone to the car’s bluetooth
ok, now we have announced that exciting mod here is something slightly cooler:
///M-Track Mode! (The 3/4 arrow, to the left of the butterfly mode symbol)
I found some good instructions online for coding MTM, spent some random free time researching how to code and use the software and today I finally felt comfortable enough to risk bricking my modules and tried it out.
MTM was offered on the CSL and ZCP cars and is a more lenient stability control system that lets you slide but not spin.
Pressing the DSC button enters MTM, holding it for 5 seconds turns DSC fully off. I will try it out at Blackhawk in September!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login