WIBIMMERS

I attempted to fold my nissans mirror and it fell off.. new level of foldage..?

nice thing with the n52/54/55..er..basically any new bmw  is the electric water pump/thermostat . it starts blowing heat very quickly because it keeps the pump off or on very low till the coolant warms up.. and even when its cold the factory tune limits boost to somewhere around 5 psi till oil is 120f

i let mine run for like a minute when its super cold. otherwise i start driving

I dont think blasting valves with walnuts is iilegal lol thanks guys

patsbimmer1 said:

Mann bhear pigg?

Im so serial right now..

New here but long time bmw owner, im offering to blast and clean n54 and n55 valves for 180 !

also if you let me know ahead of time, i can slap a new oil filter housing gasket on for an extra 30(you bring the gaskets)

Pm me for details

Im located in N. Fond du lac wi

And i do this out of my garage at home

parts for oil filter housing gasket if you obtain, you need at least the o.f.h. gasket and the oring, if you have an oil cooler all 3!

gasket for housing pn below(same gasket for non oil cooled and oil cooled models). number 4 on diagram

11427537293

gasket for oil t-stat housing(oil cooled models only). number 5 on diagram

11427525335

oring for water pipe. number 8 on diagram

11537545278

I bought the pump from muller mototwerks.and the owner personally delivered me a new pump the next day and printed me a return label. It dont get better than that. Awesome guys

It is mandatory for every n54/n55 owner to pay me a visit.

I also do the backend flash for n54 guys and pretty much anything else!

Heres mine on the dyno

Ive been there twice for dyno runs on my 335i, its also where i get my parts from, these guys rock, welcome!

tsweers89 said:

Were do you work? As i know this isnt your full time thing at these prices. Not even worth most peoples time to do it for that cheap.

Used to work at oshkosh truck as a heavy armor welder and repair welder

Now i work at metalcraft of mayville as a robotic/manual welder making parts fot scag,john deere,and cat.

The rear on an e92 looks like it got sucked into a black hole halfway...lololol and i like my dime a dozen 4 door, and your lug nuts are weird mike XD

just added that if you bring the gasket(s) for your oil filer housing i can swap them out for 30 bucks while where in there!

pm me for parts needed if you dont know. but oil cooler modles have an extra gasket for the t stat housing for the cooler.

 and you need the little oring for the water pipe as well. then the base gasket. i dont keep the parts here but if you need . i can order them for you and you can pay for them with the job

gasket for housing pn below(same gasket for non oil cooled and oil cooled models). number 4 on diagram

11427537293

gasket for oil t-stat housing(oil cooled models only). number 5 on diagram

11427525335

oring for water pipe. number 8 on diagram

11537545278

There be dirty valves out there, i shall destroy the carbon tar of death! Thanks pat!

Lol my member title is "nut blaster "XD

Happy114 came down for the blast and waterpump, these where his valves 101k, nasty! But spotless now

Still doing this. Hit me up

patsbimmer1 said:

Will you backend flash me?

I would

gonna be blasting a vw fsi 2.0 turbo engine by Wednesday. should be interesting to fabricate a vac tube for that. BUT i got room for more ppls! let me at your valves on nastiness!

im back! lol ive been really busy with work. and cold sucks..but im doing it again..please anyone who needs this done get a hold of me