Non-BMW Stuff on a BMW Forum
-
The last month was pretty crazy figuring out this whole lighting biz. But I got caught up on the first wave of orders and had a night to just work on the car.
It's back on the ground. What I've completed up to this point:
- ABS Delete using the Chase Bays brake line kit.
- Chase Bays power steering reservoir and hoses.
- Patch some rust in the engine bay and paint it.
- New water pump, timing belt kit, transmission input shaft seal.
- Ditched the Garagistic DSSR in favor for the IE Motorsports DSSR and oem shift selector joint.
- Rebuilt the HVAC box with all new foam on the flaps and the joints and fixed one of the recirc flaps.
- Redid the body harness going into the engine bay (lights, fan, etc.) with new loom.
What's left:
- Finish putting interior back together and redo the gauge wire harnesses.
- Paint a couple pieces.
- Fluids.
- Odds and ends.
My printers hard at work.
These lighting adapters have been a lot of fun and really cool to see all of the reactions to them. I'm trying really hard to make them look and feel just as good as they do function.
-
The last month was pretty crazy figuring out this whole lighting biz. But I got caught up on the first wave of orders and had a night to just work on the car.
It's back on the ground. What I've completed up to this point:
- ABS Delete using the Chase Bays brake line kit.
- Chase Bays power steering reservoir and hoses.
- Patch some rust in the engine bay and paint it.
- New water pump, timing belt kit, transmission input shaft seal.
- Ditched the Garagistic DSSR in favor for the IE Motorsports DSSR and oem shift selector joint.
- Rebuilt the HVAC box with all new foam on the flaps and the joints and fixed one of the recirc flaps.
- Redid the body harness going into the engine bay (lights, fan, etc.) with new loom.
What's left:
- Finish putting interior back together and redo the gauge wire harnesses.
- Paint a couple pieces.
- Fluids.
- Odds and ends.
My printers hard at work.
These lighting adapters have been a lot of fun and really cool to see all of the reactions to them. I'm trying really hard to make them look and feel just as good as they do function.
Dang you went all in on the print farm! That light output/cutoff looks super nice.
-
Dang you went all in on the print farm! That light output/cutoff looks super nice.
As I started making them I realized that a complete kit takes 24 hours of non stop printing to make with one printer. Since I really only have the ability to start a print on the morning and after work, it wouldn’t have been good business to do that. Plus, if the printer went down, then I’d be screwed. So yeah, I dove right in.
-
I keep seeing your posts in r3v, I really hope this takes off!
that plug and play option is super tempting -
I keep seeing your posts in r3v, I really hope this takes off!
that plug and play option is super temptingMe too!
Its harder than I anticipated. I knew forums didn’t work like they did years ago for selling car stuff and that’s it’s all moved to Facebook and Instagram, but I never got deep into instagram. So it’s been a huge learning curve to try and get the name out there.
But those who have received and installed the adapters really like them!
The Depo kits with the new Acme projectors is a no brainer to me. I was taking some new pictures of them last night and I’m looking at the Depos , and then my Ellipsoids, and back to the Depos. If one of those sets end up on my car I won’t be surprised.
-
i see you are reselling DEPO kits. just a fair warning - their quality is subpar. I can tell you are dedicated to selling a really great product, and the DEPOs are not up to those standards. just have your customer service person ready to field those calls
a suggestion: be willing to open a set of the DEPO lights and sell replacement parts from it if someone requests. no other vendor does this. you may actually get business from this alone, and it would also support your own product. youll have to learn to disassemble (and/or make some special tools) without breaking stuff, but it doesn't take much practice.
what i've personally seen/experienced:
1. broken or stripped adjuster knobs (plastic is bad quality)
2. broken glass (thinner glass than oem, cracks easier)
3. leaking seals. (the gasket on the back bulb covers and the o-ring on the parking light are a joke)
Dan
-
i see you are reselling DEPO kits. just a fair warning - their quality is subpar. I can tell you are dedicated to selling a really great product, and the DEPOs are not up to those standards. just have your customer service person ready to field those calls
a suggestion: be willing to open a set of the DEPO lights and sell replacement parts from it if someone requests. no other vendor does this. you may actually get business from this alone, and it would also support your own product. youll have to learn to disassemble (and/or make some special tools) without breaking stuff, but it doesn't take much practice.
what i've personally seen/experienced:
1. broken or stripped adjuster knobs (plastic is bad quality)
2. broken glass (thinner glass than oem, cracks easier)
3. leaking seals. (the gasket on the back bulb covers and the o-ring on the parking light are a joke)
Yeah, I hear you. I added a note to the website reiterating that they're an aftermarket headlight and not an OEM replacement.
I would like to think that most people know what Depo headlights are and that they are an affordable aftermarket option/alternative to OEM headlights. The ones I've taken apart though, the quality seems fine. I'll mess with the adjusters some and doulbe check any that go out.
Fun fact I recently learned with the printers and those cheap color changing LED light strips with remotes from amazon. The interference from the receivers on the light strips is enough to "push" the button on the printer's menu and make it do things by itself. I pulled those out of each one and put in LED under cabinet type lights and have had no issues.
-
I would like to think that most people know what Depo headlights are and that they are an affordable aftermarket option/alternative to OEM headlights. The ones I've taken apart though, the quality seems fine. I'll mess with the adjusters some and doulbe check any that go out.
think all you want, but your brain power will not transfer to the morons of the world
Dan
-
It looks OEM. Very nice job.
-
Tried this thing. It didn't work though due to the GAPING HOLE IN THE WATER PUMP GASKET I found after filling it up with coolant.
Replaced the gasket and then it worked and made filling it up really easy.
Some interior dingle berries to wrap up. Just waiting for the classic wisconsin 30 degrees and snow to 80 degrees and humid over night transition to summer.
-
Does anyone have any suggestions for making the horn button work on the aftermarket settering wheel? There's one wire that comes into the hub, and if I ground that out on the steering wheel, the horns engage their horning. The button has two spades, so obviously I need to ground one of them. Any suggestions on how to ground that within the steering wheel?
-
Does anyone have any suggestions for making the horn button work on the aftermarket settering wheel? There's one wire that comes into the hub, and if I ground that out on the steering wheel, the horns engage their horning. The button has two spades, so obviously I need to ground one of them. Any suggestions on how to ground that within the steering wheel?
Momo makes this horn button retainer plate thing (here is one example, have no experience with this specific part though: https://www.ebay.com/itm/121532035439) that has a grounding point on it. I believe it connects the ground through the steering column like the OEM horn buttons. This is what I did on my car with some modification to the ring as I'm using a raid steering wheel (though I am using a momo wheel hub) and it works perfectly. Wired like this:
-
Momo makes this horn button retainer plate thing (here is one example, have no experience with this specific part though: https://www.ebay.com/itm/121532035439) that has a grounding point on it. I believe it connects the ground through the steering column like the OEM horn buttons. This is what I did on my car with some modification to the ring as I'm using a raid steering wheel (though I am using a momo wheel hub) and it works perfectly. Wired like this:
That looks like exactly what I need! Thanks for that. I had no idea that existed.
-
Question time. Tonight I realized my cruise control is not working. It was working completely fine before everything this winter. The only thing I did to the cruise control system was replace the cable from the actuator to the throttle body.
I followed this diagnosis list:
1. low resistance between pin 9 and ground (both the ground on the connector and the chassis)
2. switch the meter to volts and while I do get power, I’m getting about 11.2v between pin 9 and earth while the battery is at 12.5v
3. connect a bulb between pin 1 and 24. This worked and the bulb turned on.
I guess I’m wondering what else I can check? I think it’s weird I’m not getting full voltage in #2.
Can somsone who's better at wiring break this down for me:
What does that mean and is there a way to test that?
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login