The E46 M3 Journal
-
Maybe. I was all over Milwaukee yesterday I can't remember my time frames.
Stock tune to come today.
I also had a nightmare that the M3's head gasket blew. I have to get these cars fixed!! Haha
@DrLeadFoot
-
The stock tune made a huge difference being that the car doesn't sound like a old ford pickup with a bad exhaust manifold gasket. The light still came on. After talking with Frank Smith from tuning tech we think the 2 cam and crank sensors should be replaced. I will order those tomorrow. I'm thinking that is why the car doesn't start on the first try. I also have replaced almost everything else that would throw the o2 sensor codes.
@DrLeadFoot
-
Break My Wallet So the car runs better on the stock tune then?
I'm thinking the file that was on the computer that he made the tune off of was of the car running poorly.
I'm getting the 2 cam sensors and crank sensor tomorrow to see if that fixes the problem.
@DrLeadFoot
-
Next to do after I replace the sensors. The music gets you in the wrenching mood.
@DrLeadFoot
-
Ordered cam and crank sensors. Should be in tomorrow afternoon.
@DrLeadFoot
-
For reference :
http://www.e46fanatics.com/forum/showthread.php?t=862891
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Didn't take pics but I replaced the intake, exhaust and crank sensors.
Cleaner the throttle bodies and checked if they were adjusted properly.
Cleaned the inside of the intake manifold.
Cleaned the ICV.
Properly connected the SMG Reservoir line and topped it off with fluid. It was leaking.
Replaced what I think was the fuel relay.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Took it for a 66 mile drive late last night. No engine light after I cleared the adaptations. However, I'm still not 100% positive it's fixed.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Is the performance what it should be?
It does feel good. I'm about to get some coffee and go for a long drive.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Too lean codes popped up banks 1 & 2.
Checked for vacuum pressure ant it looks perfect.
Going to clean the MAF and re-seal it in the housing.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Could this be the problem?? It is really dry and cracked
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Smoke test it for leaks in the intake track or such. Start there. Also gas cap will not cause those faults. Would be evap faults. I'm lost as to why you continue to throw parts at it and not have someone with the know how diagnose it properly. Just look at all the parts you installed that wernt needed.
-
Timmy, it has been tested for vacuum leaks. I replaced the pre-cat O2 sensors w/OEM parts. I have 137K on the motor. Why not replace the cam sensors? New MAF due to the too lean codes.
What is the problem if you're so knowledgeable? Where would you start?
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
I'd personally drop it off at Matts shop down the street from Concours and have him diagnose this issue. Without being there I cant really tell you what to do. Usually a bad maf will cause a rich mixture though not lean. What are the multiplicative and additive fuel adaptations values? Have you drove and checked fuel pressure? What about injectors starting to clog? Bad ecu? Exhaust leaks? Etc. All things that can cause lean mixtures. Without the car in front of me I can't diagnosis obviously. You sound like you don't know were to go as you are taking everyone else's advice and throwing parts at the issue. Also sure you have 137k on the motor...so what? Why don't you rebuild the motor then as "preventive maintenance" i mean were does it end? You know people at concours to. Why can't yout have them take a peek?
-
There is value in learning about your car and increasing your diagnostic ability and engine knowledge by troubleshooting and working out problems yourself. You spend extra time and money doing so but valuable experience is gained.
Another reason to go at it yourself is the lack of trust and credibility a lot of shops have.
I use shops pretty much just for tire mounting and alignment since the required tools arent available for my personal use. Even then it gets difficult to deal with the incompetency of shops.
The last two experiences I had with shops were
-they didnt have the "special bmw tool" to do an alignment on my E30 which only has adjustable toe
-On a Nissan Versa they quoted an extra $39 for tire mounting to re-program the TPMS sensors "so the car will know which corner has which sensor". Re-install the wheel from the same corner you removed it from then???? "Nope it just doesnt work like that"
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login