ClassE 1989 325IS Build Thread
-
Well.... Might have found the culprit for my slight grinding from rear. Not sure:
Rotated wheel ends from both sides - couldn't hear anything troublesome, only noise was a slight "whine" from diff. So put new pads in passenger side and reassembled - turned over to same results. Put rotor back on drivers side and turned over by hand. "GGRRIIINNDDD"
Ruh-oh
Checked to make sure ebrake was fully disengaged, rotated again and got the same sound. Removed rotor and found these on inside of rotor:
2 separate cracks, about 60 degrees apart. I swapped rotors side-to-side and got same grinding.... So not sure if it's the issue.
Shoes are seated firmly against backing plate, springs seem to be under good tension, and brake appears to be operating normally. There was some heat cracking on shoes - but not excessive wear.
Thoughts?
Don't have a lot of experience replacing shoes/springs, so will have to do some research in the AM.
-
That ITB setup would be fantastic! That car must be horridly slow or obnoxious to drive though
How do you figure?
-
The M20 is quite well optimized out of the box and in my opinion the two areas where people go horribly wrong on NA M20 builds is changing to a piston which does not match the squish area of the combustion chamber and not taking advantage of pressure wave tuning on the intake manifold.
-short runner length/no plenum
-low air velocity at low rpm with itbs
-large camshaft required to match intake selection
-high compression pistons required to keep static and dynamic compression ratios happy due to large cam
-pistons without the proper squish area due to the requirement to have high compression as well as valve clearance due to large cam
It would be like disabling the VTEC system on a honda. It's removing the secret sauce that makes it perform the way it does.
-
Voting for polished V12 manifold.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
I happen to have 3 extra m20 intake manifold I could cut up and make manifolds with!
I would very much so like to do a set of ITB's
I could be the test dummy for this, and fabricate it as well, but I need a little help designing! Which throttle bodies would you use? Or would you build your own?
I could start on this whenever! I would like to see an hx40 on my brothers e30 along with some ITB's. I think it would be perfect.
sk8 or die
-
When I was toying with the calculations I believe I determined that the stock M20 manifold operated on either the 2nd or 3rd harmonic. If you guys are serious about a custom manifold then I would be willing to dive into it again for size/length calcs to see what it would look like or if its even possible to do a 1st harmonic tuned manifold.
-
When I was toying with the calculations I believe I determined that the stock M20 manifold operated on either the 2nd or 3rd harmonic. If you guys are serious about a custom manifold then I would be willing to dive into it again for size/length calcs to see what it would look like or if its even possible to do a 1st harmonic tuned manifold.
When I was toying with the calculations I believe I determined that the stock M20 manifold operated on either the 2nd or 3rd harmonic. If you guys are serious about a custom manifold then I would be willing to dive into it again for size/length calcs to see what it would look like or if its even possible to do a 1st harmonic tuned manifold.
Yea I'm Seriously serious. I have the resources to produce a couple real quick. And I wan't one
sk8 or die
-
I have been eyeing up parts from these guys for awhile:
I hadn't thought much on bike carbs or such - let me do some thinking on that. I was invisioning buying an ITB set-up and customizing the stock lower portion of the original manifold to accept the bolt pattern.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login