Savin Big Money Project Thread

[jc43089]

Here we go, First was out having some fun driving the cruiser.

Here is the pile of undercoating so far.

Rear subframe reinforcements.

Rear trailing arm pockets.

Then I made an air dryer for sandblasting.  Here is what the inside looks like.

Finished.  When you want dry air, connect the air so it goes through, and fill the PVC tube with ice.  Air temp drops, moisture condenses and stays in the bottom of the loop, then just drain periodically from the copper line.  It will be mounted to the wall and then can be drained of water from the ice melting with the PVC valve at the bottom into a bucket.  After going through this it will go into a filter as well.

Then I cleaned up the garage, it was getting pretty bad.  Messy garage = poor productivity.

My piles of parts are kinda scary so close to spring...

And a few parts that were powder coated.  Kawasaki black.

Got a sandblaster from HF so next week I will try to get the shell into the driveway and start blasting.

And my new awesome garbage can.

[YoungCR]

How are you gonna move the car out of the garage? I've always been curious if 4 1000# mover dollies ($20 each at HF) could serve as car dollies for a bare shell.

[bfinley]

Looking forward to see how the blasting goes!

Let me know when you want help putting all those parts back in, 3 of us could get her back together in a weekend easy

[Jdesign]

CYoung said:

How are you gonna move the car out of the garage? I've always been curious if 4 1000# mover dollies ($20 each at HF) could serve as car dollies for a bare shell.

It works, I have used them in the past, and my civic shell is setting on three of the wooden ones at the moment! 

[Jdesign]

BTW that air dryer is brilliant!

[jc43089]

CYoung said:

How are you gonna move the car out of the garage? I've always been curious if 4 1000# mover dollies ($20 each at HF) could serve as car dollies for a bare shell.

This is the plan, as long as I get it down low before moving it shouldn't be a problem, FYI if you have the drivetrain out of an e36 and have the jackstands on the factory pads you can lift the front end by yourself.

bfinley said:

Looking forward to see how the blasting goes!

Let me know when you want help putting all those parts back in, 3 of us could get her back together in a weekend easy

I will probably be on hold for a little bit, helping Mike with his e28 on Tuesday and then I might get the e30 home and start the trans swap in the driveway.  I am going to be working 5 tens a week at work from April until July at least so that sucks for BMW productivity but OT is nice. 

Jdesign said:

BTW that air dryer is brilliant!

Thanks!  I hope it works.  I think by using the 3/4" pipe the air will slow down enough to cool effectively.  It is also pretty compact which is necessary in my one car garage.

[RamRod E28]

I bet u Ben and I could get ur e36 pretty far in a weekend. You gotta get her done soon cause the spring in spring green meet is almost upon us

[bfinley]

Ramze46 said:

I bet u Ben and I could get ur e36 pretty far in a weekend. You gotta get her done soon cause the spring in spring green meet is almost upon us

True story, course days notice and I'll clear a weekend. Plus I need a BMW ride to the meet since mine is on almost as many pieces as the e36

[RamRod E28]

You may be able to get a ride in the e28 at the rate that thing is getting done!

[jc43089]

I will be cruising the e30 to the meet!

Today the interior comes out, and going to build a cart sorta thing to move the shell around.

Got the driver seat out, they are ridiculously heavy!

[bfinley]

VERT! Riding in style. Are there airbags in the seat ?

[jc43089]

No airbags in these ones, but they are power/heated.  Probably close to 50 pounds each.

[bfinley]

Yikes

[jc43089]

Dash and carpet out, floor looks ok from the inside.  Lots of sticky residue under the carpet, looks to be spilt soda...

[bfinley]

Gross, does it have the black tar layer like mine did ?

[jc43089]

Yea, working on that now.

[bfinley]

Heat gun makes that go super easy

[jc43089]

Good call, that is working way better.

[RamRod E28]

More e36 carnage?

[jc43089]

Yup, pics when I'm done.