'88 E30
-
Hell yeah! Even with the M10 in my car, I had a blast. Was planning to do a lot more this year, but didn't get the car together soon enough. FVSCC has an event on the small track at Road America this weekend that I'm hoping to make it to. Should be a lot more fun now. I get TONS of body roll. Should really work on the suspension.... but turbo...
Need to get the car together by May next year instead of late July...
-
Harness covers installed
-
How do you have the radiator clip holding the radiator?
Rubber feet on the bottom of the rad rest on the core support. Top clip has rubber feet pushing against top of rad and the clip is then screwed into the core support
-
Stock right? That's how the radiator on my brothers e30 is secured.
You bet!
-
Basically just been collecting tools and acquiring parts for this winters project. (Which is pretty much everything that moves under the unibody)
Got the space setup. Windows have been great stuffed and plastic sealed. Torpedo heater is good to go and the parts are very very slowly rolling in, big thanks to Garagistic. Got the complete chassis and trailing arm reinforcements in/on their way and every bushing has been ordered except for the diff. The drive shaft was brand new as well as the flex disc when I did the swap.
Left to order:
Diff bushing
Every braking component
Still on the fence about sway bars
Coilover setup
So basically waiting for the bulk of it yet
Will be pulling both front and rear subframes & most likely will get rid of those as I'm getting some rust free ones from a parts car so I can refresh a good one while the car sits
Front subframe and suspension will come out while harbor freight holds my engine in the balance
Should be fun, I also stocked up on map gas, PB blaster, impact, and have been practicing my breathing techniques for when this junk won't come out easily
-
I like your breathing exercises!
I really have not run into anything that doesn't come apart with a reasonable amount of force, the rear subframe bushings are what I would think to be the trickiest part of the suspension to get out, but there are tricks for that as well.
A whole suspension refresh will feel awesome, I know mine did when I did it. You actually get to drive yours so it will be that much better
-
I like your breathing exercises!
I really have not run into anything that doesn't come apart with a reasonable amount of force, the rear subframe bushings are what I would think to be the trickiest part of the suspension to get out, but there are tricks for that as well.
A whole suspension refresh will feel awesome, I know mine did when I did it. You actually get to drive yours so it will be that much better
This is what I'm excited for. In all honesty when I rode in snaps properly setup m20 car (NA) it felt soooo much better than my car right after I did the s50. Suspension makes such a huge difference, I had to feel it to believe it (no homo)
-
What material bushings are you going with?
Any plans for CAB's? -
Poly (95a) for subframe
Poly (95a) for diff
Solid Delrin RTABs
Solid offset Delrin FCABs
Engine & trans are already solid Delrin
-
That garage looks great!! Times like these are great in the build world. Excited for you!
FYI, I might be selling my turbo manifold, turbo, and full 3in stainless exhaust next winter...
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
That garage looks great!! Times like these are great in the build world. Excited for you!
FYI, I might be selling my turbo manifold, turbo, and full 3in stainless exhaust next winter...
Sent from my SM-G900V using Tapatalk
-
Hover car
Every last bolt I need to remove I've soaked in PB blaster
Tires are under it in case harbor freight decides to let me down big time
Tools of the hopeless
Plan is to drop both front and rear subframes with as much crap intact as possible.
I snuck a peek at the RTABs and holy shit. They needed to be replaced about 4 lifetimes ago
-
Everything in the front is out
Parts are all in desperate need of being recycled. I will be cleaning up the rack, getting new tie rods, new boots, etc.
Everything came out super easily. Steering rack linkage was the biggest PITA, but came out okay once the subframe was out
Parts came in today too!
-
Nice work man!! Are those reinforcement plates and such you got?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login