'88 E30
-
It runs
Added coolant after making sure it ran and wouldn’t eject belts.
Will need to bleed coolant and finish bleeding the power steering
Bleed brakes as well, clutch was fine
There’s tons of loud valve train noise, going to assume it’s because of a completely fresh vanos and completely refreshed head, as in, need to bleed the lifters and get oil into everything. Same thing happened when I originally put the s50 and started it (albeit this time around is much louder, probably because I never removed the head last time-who knows).
Basically now it’s bleed coolant, bleed/flush power steering, finish up the gauge panel and figure out why the hell my e30 temp gauge immediately pegs red hot when you turn the key on. Going to try and swap the temp sensors as I do not remember which one goes where
Hopefully worst case scenario is I have a bad temp sensor (unlikely as they are new)
-
Oh also I need to go to an exhaust shop eventually, these headers won’t work with the mid pipe I have which is super convenient
-
Woohoo! That must have felt good!
For temp sensors, make sure the connector with only one contact in it is on the brown temp sensor (or single pin, they are sometimes clear).
I'm stoked to see more of this!
-
Rattling is normal after sitting for a long time. Hold the rpms around 3k for a little while and it will pump the lifters back up. Almost ready for burnouts/axle breakage!
For sure!
Different angle
-
yes, i demand many burnouts and axle breakage ! A lot of 'yes' right here. Love the sound of the motor firing up
2011 E92 M3 6MT ZCP - ESS 625 supercharged
2007 Z4MR
2003 E39 M5
2002 E46 M3
2021 X5 40i -
Woohoo! That must have felt good!
For temp sensors, make sure the connector with only one contact in it is on the brown temp sensor (or single pin, they are sometimes clear).
I'm stoked to see more of this!
They both have 2 contacts
-
Swapped connectors. Gauge doesn’t jump full hot when I turn the key on now. Should be good.
FYI, both e36 obd1 harnesses I have indeed are two pin connections for the temp sensors. Only 1 pin sensor I can find that is close (distance wise) would be for the oil pressure switch.
(Manifold temp sensor may also be 1 pin as well - but I ruled this out because the length of the harness is a dead give away to where it connects to)
-
Awesome! I can't wait for a ride!
-
Swapped connectors. Gauge doesn’t jump full hot when I turn the key on now. Should be good.
FYI, both e36 obd1 harnesses I have indeed are two pin connections for the temp sensors. Only 1 pin sensor I can find that is close (distance wise) would be for the oil pressure switch.
(Manifold temp sensor may also be 1 pin as well - but I ruled this out because the length of the harness is a dead five away to where it connects to)
Awesome that this thing is so close!
I know that the way I have my car set up is one connection is for the gauge, the other is for the ecu readout, and if you flip them, the guage would pin itself. Same with my E24, but that has one single pin, and a double pin. I have had the luxury of finding this out with both cars. lol
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
Bleeding coolant tonight, also will try and get the head “bled” tonight as well at the same time, it was loud on startup
-
Bleeding coolant tonight, also will try and get the head “bled” tonight as well at the same time, it was loud on startup
Rumor has it that burnouts (with videos) actually clear this up the quickest.
-
KaiserRolls said:
Bleeding coolant tonight, also will try and get the head “bled” tonight as well at the same time, it was loud on startup
Rumor has it that burnouts (with videos) actually clear this up the quickest.
Is like to 2nd this
1976 530i e12
1990 325ix e30
1992 325i e36
1995 740il e38
2001 330xi e46
^More to come
-
First and last drive of 2017 happened today.
Until next spring!
-
Well, MS3 Pro is on the way.
Never really liked the idea of the chiptune and no datalogging capability.
Thankfully the turbo Miata has been a good learning experience
-
Never really liked the idea of the chiptune and no datalogging capability
I have spent a few hours already looking at piggybacks, emulators, and logging systems for OBD1. There just isnt a proper tuning solution that doesn’t involve guess and check.
Nothing will run a stock-ish engine better than a stock DME, but a completely different EMS like megasquirt is really the only solution if you want it dialed in 100%
Logs are awesome
-
Showed up, now it’s time to get a not crappy laptop and get everything ready to go
-
YESSSSSSSSS.
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
Picked up some scaffolding from MN this morning
Before install I will fog it black
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login