'88 E30

[Jdesign]

KaiserRolls said:

Swapped connectors. Gauge doesn’t jump full hot when I turn the key on now. Should be good.

FYI, both e36 obd1 harnesses I have indeed are two pin connections for the temp sensors. Only 1 pin sensor I can find that is close (distance wise) would be for the oil pressure switch.

(Manifold temp sensor may also be 1 pin as well - but I ruled this out because the length of the harness is a dead five away to where it connects to)

Awesome that this thing is so close! 

I know that the way I have my car set up is one connection is for the gauge, the other is for the ecu readout, and if you flip them, the guage would pin itself. Same with my E24, but that has one single pin, and a double pin. I have had the luxury of finding this out with both cars. lol

[KaiserRolls]

Bleeding coolant tonight, also will try and get the head “bled” tonight as well at the same time, it was loud on startup

[GunMetalGrey]

KaiserRolls said:

Bleeding coolant tonight, also will try and get the head “bled” tonight as well at the same time, it was loud on startup

Rumor has it that burnouts (with videos) actually clear this up the quickest.

[Jeff]

GunMetalGrey said:

KaiserRolls said:

Bleeding coolant tonight, also will try and get the head “bled” tonight as well at the same time, it was loud on startup

Rumor has it that burnouts (with videos) actually clear this up the quickest. 

Is like to 2nd this

[KaiserRolls]

First and last drive of 2017 happened today.

Until next spring!

[Jeff]

KaiserRolls said:

First and last drive of 2017 happened today.

Until next spring!

How fast where you going when the hood came off???

[KaiserRolls]

Well, MS3 Pro is on the way.

Never really liked the idea of the chiptune and no datalogging capability.

Thankfully the turbo Miata has been a good learning experience

[B C]

KaiserRolls said:

Never really liked the idea of the chiptune and no datalogging capability

I have spent a few hours already looking at piggybacks, emulators, and logging systems for OBD1. There just isnt a proper tuning solution that doesn’t involve guess and check.

Nothing will run a stock-ish engine better than a stock DME, but a completely different EMS like megasquirt is really the only solution if you want it dialed in 100%

Logs are awesome

[KaiserRolls]

Showed up, now it’s time to get a not crappy laptop and get everything ready to go

[Jdesign]

YESSSSSSSSS.

[KaiserRolls]

Picked up some scaffolding from MN this morning

Before install I will fog it black

[Jdesign]

[B C]

Lovely engagement photo, Mr and Mrs Kaiser!

[KaiserRolls]

Drove it home from storage today
Promptly folded the mirrors
See you fuckers in 2019

[B C]

snap said:

Lovely engagement photo, Mr and Mrs Kaiser!

[Rekpoint]

KaiserRolls said:

Drove it home from storage today
Promptly folded the mirrors
See you fuckers in 2019

C&C on April 14th?!?!?!?

Sent from my SM-G955U using Tapatalk

[KaiserRolls]

Rekpoint said:

C&C on April 14th?!?!?!?

Sent from my SM-G955U using Tapatalk

4/14/2019

See you there

[KaiserRolls]

In the quest to lower intake temps, I have come to a realization.
After much deliberation with snap, wasntm3 & staring at the engine bay for hours- air to air and air to water Intercooling have been tossed as there is not sufficient room. Which leaves meth injection as the remaining option.
Next up on the to do list is to replace the intake & charge pipe with something a little less plastic that can hold some threads and dissipate heat better than the 1/4” thick abs.
Also I know my MS3 can control the spray, but at this point I’d rather get something that has its own controller for simplicity sake.
If anyone has some experience with any specific meth kits or if you’ve pieced your own together I’d love to hear about it.
Was looking at devils own/aquamist/snow performance

Picture of 20lbs of shit in a 10lb bag

[Jdesign]

After rotating my head 90 degrees onto my shoulder, I noticed that you have lots of ample room for all sorts of things on the left side of your engine bay......

air to air and air to water Intercooling have plenty of room to party over there.

[m42b32]

Info on the Moroso coolant expansion tank? I wont be able to use the Zionsville setup anymore and that looks like a nice solution.