Wheel refinishing

[Rekpoint]

stealthbimmer said:

What kind of wheels are on the right?

[Earl]

They're Fittipaldis=) Corvette fitment I assume?

[stealthbimmer]

Jdesign said:

BFRM(BigF*ckingRubberMallet) and blocks of wood for removing the faces. I  normally use an impact removing wheel hardware. 

That's what I figured. They are really correded. Impact would probably be fine on wheels that aren't in such bad/corroded condition....or use a bolt and nut. First one came out fine. Second one snapped. I did the whole wheel with a breaker bar and ratchet in like 5 minutes, so not worth the risk to save mere minutes

Sent from my SM-G930R4 using Tapatalk

[stealthbimmer]

Earl said:

They're Fittipaldis=) Corvette fitment I assume?

They are indeed fittipaldis.

17x8.5 I believe

5x120 et13

I think I have only come across like one other set with the same specs. They need to be finished though. I have the faces stripped and the lips sanded. Two barrels have bends or cracks so I need to get those taken care of before anything. I have been sitting on them for years.

Sent from my SM-G930R4 using Tapatalk

[stealthbimmer]

Welp. Only one wheel let me have its bolts free of charge. As for the others, they were snapping even with only using the breaker bar. I even tried heat first....they were destine to break. Anyways, I said F it and just took the impact to them all.

This was the end result

So, not sure what I am going to do with these at this point. I still havent been able to get a face seperated from a barrel. So, if I cant even do that, nothing is going to happen. Worst case scenario is Im out $50 and I plastidip the one good one and hang it on a wall or something.

[Jdesign]

So do the face bolts thread into the barrels? Did you try using heat? Getting all those snapped bolts out of there is gonna suck if they are still in the barrel. 

As far as removing the face I would just use wood, a foam floor tile and work around the perimeter until its off. Or make a jig like this guy LOL:

[straight6pwr]

scrap aluminum alloy wheels are something like $0.50/lb

with the weight of these boat anchors, your looking at $40-50 if you scrap these.

[Jdesign]

straight6pwr said:

scrap aluminum alloy wheels are something like $0.50/lb

with the weight of these boat anchors, your looking at $40-50 if you scrap these.

[stealthbimmer]

Jdesign said:

So do the face bolts thread into the barrels? Did you try using heat? Getting all those snapped bolts out of there is gonna suck if they are still in

Yes bolts thread into barrel. I tried heat. The bolts that broke were going to brake no matter what. They are just that corroded. If I can ever actually get a face off I will see if the snapped bolts are even removable. At this point I am likely just writing them off as a lost cause.

Sent from my SM-G930R4 using Tapatalk

[stealthbimmer]

straight6pwr said:

scrap aluminum alloy wheels are something like $0.50/lb

with the weight of these boat anchors, your looking at $40-50 if you scrap these.

Hey atleast I would get the $50 I paid for them back

Sent from my SM-G930R4 using Tapatalk

[Rekpoint]

*Cough* Someone *Cough* Should do this *Cough*

[Earl]

https://www.bimmerforums.com/forum/showthread.php?2148128-Anyone-removed-a-stripped-or-broken-bolt-from-a-two-piece-wheel-(Style-42-or-71)

[stealthbimmer]

Earl said:

https://www.bimmerforums.com/forum/showthread.php?2148128-Anyone-removed-a-stripped-or-broken-bolt-from-a-two-piece-wheel-(Style-42-or-71)

None of my bolt heads stripped.

[Earl]

It says "or broken" right in the title lol. I was posting it just to show that you can buy new bolts and that they're surprisingly titanium.

[Jdesign]

nice link Earl!

[Rekpoint]

If u are planning on scraping them I might try to buy one from you to make that a PC case like I showed above. Need to take measurement of my stuff though.

Sent from my SM-G955U using Tapatalk