Skip to content
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Groups
Skins
  • Light
  • Brite
  • Cerulean
  • Cosmo
  • Flatly
  • Journal
  • Litera
  • Lumen
  • Lux
  • Materia
  • Minty
  • Morph
  • Pulse
  • Sandstone
  • Simplex
  • Sketchy
  • Spacelab
  • United
  • Yeti
  • Zephyr
  • Dark
  • Cyborg
  • Darkly
  • Quartz
  • Slate
  • Solar
  • Superhero
  • Vapor

  • Default (No Skin)
  • No Skin
Collapse
WIBIMMERS logo

WIBIMMERS

  1. Home
  2. General Discussion
  3. BMW Discussion
  4. E46 help. Please

E46 help. Please

Scheduled Pinned Locked Moved BMW Discussion
25 Posts 7 Posters 0 Views 1 Watching
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ThatRatRodProjectT
    ThatRatRodProjectT
    ThatRatRodProject
    wrote on last edited by
    #5

    Snap said:

    Did you recently do an oil change?

    You may want to look into cleaning the vanos solenoid(s). I dont want to send you on a wild goose chase with unnecessary tasks, but its fairly simple and worth looking into

    I will definitely be doing this I'm not due for a oil change yet but I'm going to do one today to try to remove any possible reasons why it would be acting up. Thanks for the response.

    Sent from my iPhone using Tapatalk

    1 Reply Last reply
    0
    • patsbimmer1P
      patsbimmer1P
      patsbimmer1
      wrote on last edited by
      #6

      You can't properly get a good look at the pattern for a cam sensor without a scope.  The circuit for a cam sensor is pretty simple so unless you nicked a wire while doing the evap stuff then it was nothing you caused.  The signal goes straight from the cam sensor to the ECU so the check engine light is only reporting data that the sensor is giving.  I would assume it's either vanos related or the cam sensor actually is faulty.  I'd lean towards a vanos solenoid issue.

      2011 e90 M3 - DCT, Borla exhaust, BMW Performance Black Grille, ECS Painted Corners, Ziza Angel Eyes

      07 335i Stella - sport package, BMS DCI, zhp knob, TMS cf parking brake lever, VRSF downpipes, MHD tune, H&R race springs, other stuff *SOLD*

      97 328i Lola - sport package, m50 intake manifold, m50 manifold.com install kit, custom CAI, K&N filter, Borla exhaust, FK silverline coilovers, 25.5mm front sway bar, Powerflex front sway bushings, Turner Radiator, fan delete *sold*
      95 325is *sold*
      93 nissan 240sx KA-T *sold*

      BMWCCA #473306

      Instagram @patsbimmer1

      AKA- HALLWAY PAT

      "burnouts bring babes and babes dont have time for bushings" - Kaiser Rolls

      1 Reply Last reply
      0
      • ThatRatRodProjectT
        ThatRatRodProjectT
        ThatRatRodProject
        wrote on last edited by
        #7

        patsbimmer1 said:

        You can't properly get a good look at the pattern for a cam sensor without a scope.  The circuit for a cam sensor is pretty simple so unless you nicked a wire while doing the evap stuff then it was nothing you caused.  The signal goes straight from the cam sensor to the ECU so the check engine light is only reporting data that the sensor is giving.  I would assume it's either vanos related or the cam sensor actually is faulty.  I'd lean towards a vanos solenoid issue.

        Is it common that the vanos solenoid fails or that it just gets dirty.

        Sent from my iPhone using Tapatalk

        1 Reply Last reply
        0
        • patsbimmer1P
          patsbimmer1P
          patsbimmer1
          wrote on last edited by
          #8

          Fairly common.

          2011 e90 M3 - DCT, Borla exhaust, BMW Performance Black Grille, ECS Painted Corners, Ziza Angel Eyes

          07 335i Stella - sport package, BMS DCI, zhp knob, TMS cf parking brake lever, VRSF downpipes, MHD tune, H&R race springs, other stuff *SOLD*

          97 328i Lola - sport package, m50 intake manifold, m50 manifold.com install kit, custom CAI, K&N filter, Borla exhaust, FK silverline coilovers, 25.5mm front sway bar, Powerflex front sway bushings, Turner Radiator, fan delete *sold*
          95 325is *sold*
          93 nissan 240sx KA-T *sold*

          BMWCCA #473306

          Instagram @patsbimmer1

          AKA- HALLWAY PAT

          "burnouts bring babes and babes dont have time for bushings" - Kaiser Rolls

          1 Reply Last reply
          0
          • B
            B
            B C
            wrote on last edited by
            #9

            I only ask if an oil change was recently performed because i recently heard of someone discarding an important piece of the oil filter assembly while doing an oil change. Its a frequent enough variable so i thought id ask

            1 Reply Last reply
            1
            • ThatRatRodProjectT
              ThatRatRodProjectT
              ThatRatRodProject
              wrote on last edited by
              #10

              patsbimmer1 said:

              Fairly common.

              Common fails or gets dirty.

              Sent from my iPhone using Tapatalk

              1 Reply Last reply
              0
              • patsbimmer1P
                patsbimmer1P
                patsbimmer1
                wrote on last edited by
                #11

                More get dirty but they also fail.  Neither would surprise me.

                2011 e90 M3 - DCT, Borla exhaust, BMW Performance Black Grille, ECS Painted Corners, Ziza Angel Eyes

                07 335i Stella - sport package, BMS DCI, zhp knob, TMS cf parking brake lever, VRSF downpipes, MHD tune, H&R race springs, other stuff *SOLD*

                97 328i Lola - sport package, m50 intake manifold, m50 manifold.com install kit, custom CAI, K&N filter, Borla exhaust, FK silverline coilovers, 25.5mm front sway bar, Powerflex front sway bushings, Turner Radiator, fan delete *sold*
                95 325is *sold*
                93 nissan 240sx KA-T *sold*

                BMWCCA #473306

                Instagram @patsbimmer1

                AKA- HALLWAY PAT

                "burnouts bring babes and babes dont have time for bushings" - Kaiser Rolls

                1 Reply Last reply
                0
                • dastuzD
                  dastuzD
                  dastuz
                  wrote on last edited by
                  #12

                  I know I'm late to the party and this recommendation is also potentially late...  I know on my S-motor I replace the micro filter on my Vanos unit roughly once a year.  It's super cheap, super easy to do, and I know a few people who have had a lot of luck with that preventing Vanos issues.

                  $0.02

                  1 Reply Last reply
                  0
                  • ThatRatRodProjectT
                    ThatRatRodProjectT
                    ThatRatRodProject
                    wrote on last edited by
                    #13

                    dastuz said:

                    I know I'm late to the party and this recommendation is also potentially late...  I know on my S-motor I replace the micro filter on my Vanos unit roughly once a year.  It's super cheap, super easy to do, and I know a few people who have had a lot of luck with that preventing Vanos issues.

                    $0.02

                    Thanks for the info. I will also clean that filter.

                    Sent from my iPhone using Tapatalk

                    1 Reply Last reply
                    0
                    • ThatRatRodProjectT
                      ThatRatRodProjectT
                      ThatRatRodProject
                      wrote on last edited by
                      #14

                      Well I went threw cleaned everything rest the codes. Drive about a 175 miles and SES light comes back. Plug in the scanner and it's the secondary air bank one and secondary air bank two. I have replaced the smog pump. Checked the evap valve with a vacuum pump. It was between 15" and 18" of vacuum so that's fine. So I then checked the vacuum control switch. No vacuum. Replaced the line and the switch. Still no vacuum. So next step was I check to see if I was getting power at plug for the vacuum control valve. There was power at the plug. I then tested the valve it self ran power to the control switch and the valve opened. I blew in one end air came out the other. Then I put it all back together and check it again this morning. Still no vacuum. Yes I check the fuses. Any help would be great. Good thing no more cam sensors check engine light.

                      Sent from my iPhone using Tapatalk

                      1 Reply Last reply
                      0
                      • B
                        B
                        B C
                        wrote on last edited by
                        #15

                        Standard protocol is to send donuts to those in the thread that contributed to a diagnosis

                        1 Reply Last reply
                        1
                        • ThatRatRodProjectT
                          ThatRatRodProjectT
                          ThatRatRodProject
                          wrote on last edited by
                          #16

                          Snap said:

                          Standard protocol is to send donuts to those in the thread that contributed to a diagnosis

                          Alright sounds fair

                          Sent from my iPhone using Tapatalk

                          1 Reply Last reply
                          0
                          • KaiserRollsK
                            KaiserRollsK
                            KaiserRolls
                            wrote on last edited by
                            #17

                            Or get lost and eat them yourself

                            1 Reply Last reply
                            2
                            • D
                              D
                              Daggerty
                              wrote on last edited by
                              #18

                              Are you checking for power by grounding it through the circuit?

                              1 Reply Last reply
                              0
                              • B
                                B
                                B C
                                wrote on last edited by
                                #19

                                Daggerty said:

                                Are you checking for power by grounding it through the circuit?

                                No, you dont get any donuts

                                1 Reply Last reply
                                1
                                • ThatRatRodProjectT
                                  ThatRatRodProjectT
                                  ThatRatRodProject
                                  wrote on last edited by
                                  #20

                                  Daggerty said:

                                  Are you checking for power by grounding it through the circuit?

                                  No exactly sure what you mean. Grounded to the chassis or to the plug.

                                  Sent from my iPhone using Tapatalk

                                  1 Reply Last reply
                                  0
                                  • D
                                    D
                                    Daggerty
                                    wrote on last edited by
                                    #21

                                    Are you grounding it through the plug?

                                    1 Reply Last reply
                                    0
                                    • ThatRatRodProjectT
                                      ThatRatRodProjectT
                                      ThatRatRodProject
                                      wrote on last edited by
                                      #22

                                      Daggerty said:

                                      Are you grounding it through the plug?

                                      Yes

                                      Sent from my iPhone using Tapatalk

                                      1 Reply Last reply
                                      0
                                      • D
                                        D
                                        Daggerty
                                        wrote on last edited by
                                        #23

                                        What power reading are you getting through the plug.

                                        when testing vacuum are you using your vacuum pump to build the vacuum in the system, or just to read it?

                                        1 Reply Last reply
                                        0
                                        • ThatRatRodProjectT
                                          ThatRatRodProjectT
                                          ThatRatRodProject
                                          wrote on last edited by
                                          #24

                                          I just took everything apart and put it back together. And the vacuum line was pinched on the valve cover everything is working correctly now.

                                          Sent from my iPhone using Tapatalk

                                          1 Reply Last reply
                                          1

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          • Oldest to Newest
                                          • Newest to Oldest
                                          • Most Votes


                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          Powered by NodeBB Contributors
                                          • First post
                                            Last post
                                          0
                                          • Categories
                                          • Recent
                                          • Tags
                                          • Popular
                                          • Users
                                          • Groups