Chapter GMW | E30 LS1 (starting on post #1427)
-
I on some fronts, yes. It was a junk yard motor he didn't have any knowledge of.
@DrLeadFoot
-
Not much going on lately. Trying to figure out if I should mill down my S52 block to make it perfectly straight, o-ring it and run a thicker MLS gasket. Do the putty thing in the combustion chamber to make sure I'm okay.
Or..
Build up one of these m52s that I have been slowly collecting.
Positives for decking the S52:
- Use the parts that I have
- cheapest route
- more torque
- I can learn megasquirt on a used motor
Negatives:
- there was some detonation so my rods and pistons might be shot (I really don't think they are)
- thicker head gasket makes for a weaker seal.
Build M52 positives:
- take what I've learned from the s52 build and make this one super solid
- Better head gasket seal
- can run more boost in future
Negatives :
- $$$$$$$ (house projects and getting the M3 back on the road are priority.)
- Would also like to buy a Blunttech T4 tubular manifold and a big turbo for a lot of boost. $$ (I would sell my turbo, t3 manifold, down pipe and exhaust to compensate)
- 4 in downpipe and exhaust to be made $$$
- Did I mention $$$
Please let me know your thoughts on this. Any input would be greatly appreciated.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Swap in an L*.........
Just kidding
I vote option one with the s52 since it is the cheapest route and you can enjoy the car while doing option 2 if you so please=)
I'm leaning this way. Thank you for the input!!
If I do a LS it would be in a Datsun 240/280z. I have my eye on a mint 280z at a buddies just getting dusty in his barn.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
-
Usually o-ring and MLS isn't recommended as it's a metal layered gasket. O-ring and factory gasket is what people do it O-ringing. Do you know how much you would be milling down? With low compression pistons MLS usually isn't needed. Unless you think your going to be increasing the compression that much which I wouldn't think the issue would be. Eitherway run e85 and you won't have an issue. If you think your pistons or rods have issues send them out to get analized. They can tell you with doing an xray on them. Better be safe then sorry.
-
I'm thinking MLS because I know they come in a variety of different thicknesses.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
My wife got me some "keep the faith" presents for my bday today.
Sent from my SM-G900V using Tapatalk
@DrLeadFoot
-
Not much going on lately. Trying to figure out if I should mill down my S52 block to make it perfectly straight, o-ring it and run a thicker MLS gasket. Do the putty thing in the combustion chamber to make sure I'm okay.
Or..
Build up one of these m52s that I have been slowly collecting.
Positives for decking the S52:
- Use the parts that I have
- cheapest route
- more torque
- I can learn megasquirt on a used motor
Negatives:
- there was some detonation so my rods and pistons might be shot (I really don't think they are)
- thicker head gasket makes for a weaker seal.
Build M52 positives:
- take what I've learned from the s52 build and make this one super solid
- Better head gasket seal
- can run more boost in future
Negatives :
- $$$$$$$ (house projects and getting the M3 back on the road are priority.)
- Would also like to buy a Blunttech T4 tubular manifold and a big turbo for a lot of boost. $$ (I would sell my turbo, t3 manifold, down pipe and exhaust to compensate)
- 4 in downpipe and exhaust to be made $$$
- Did I mention $$$
Please let me know your thoughts on this. Any input would be greatly appreciated.
Sent from my SM-G900V using Tapatalk
I interpret this as the eternal plight of every car enthusiast except for Jay Leno.
2011 E92 M3 6MT ZCP - ESS 625 supercharged
2007 Z4MR
2003 E39 M5
2002 E46 M3
2021 X5 40i -
I finally drained the oil or, should I say water, out of the e30...
After being in the S54 world for a little while it is very refreshing just to be under the e30 and gaze on its simplistic setup.
Making good progress on the S54/M3 stuff. Getting excited to rip that motor out and get it to the machine shop. Sitting in the shadows are 2 good m52 heads and a m52 block if anything catastrophic happened with the s52. I have to put some cheap oil in the s52 to start it and turn the car around so I can use the cherry picker out of the garage door.
@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login