My name is Earl, and I have a Stainless Steel bolt fetish =)
-
So Saturday wasn't too bad of a day.
I started by mocking up my e46 skirts
It is really hard to tell how they will look with no front fender on, and the car in the air. I would also really like to shave the raised center to give it a nice smooth look similar to the AC Schnitzer skirts.Â
After that I lubricated my cams, timing chain, and chain guides with engine assembly lube before buttoning the covers up. I then installed my upper timing cover
And then installed my water pump and thermostat housing
The thermostat housing is only on hand tight at the moment because I got the wrong gasket and my thermostat didn't come with an o-ring.Â
The valve cover is only one because I had to tighten it down to seat the timing cover on the profile gasket properly. I was told that the pressure down on it should seat the end of the profile gasket that wasn't sitting well. I sure hope it works out. I put a large dab of silicone on the inside edges like the Bentley specifies. I also put a small dab on the outside edge. If it leaks it still shouldn't be a hard fix=)
My buddy Greaser Kyle made it out and shaved all of the unneeded holes in my radiator support that you will be able to see
I found a great condition black carpet that should be shipped out today. I have also been contemplating buying aftermarket rear strut mounts since my e46 m3 vert mounts don't look like they held up too well. I was looking at either choosing Rogue Engineering mounts of the Ground Control mounts. I ended up opting for the Ground Control mounts because they are poly and seemed to be made a little beefier. Those should be shipping out today as well=)
Here is my canvas of a back window
Hopefully all of the microscratches will buff out lol
-
Achieved zero progress over the weekend. The girlfriends rear drums brakes proved to be a weekend long endeavor.Â
These came in however:
I will be installing those Saturday, as well as installing my new sway bar endlinks, bushings, brackets, and hardware.Â
I will also be getting the inside of the valve cover cleaned out and then installing it for good on the engine.Â
I gave my friend Greaser Kyle the pass code for the garage door so that he can work on the bay/shaving while I am not there so we can get this done=)
-
56 pages and the car doesnt run....im starting to feel a bit let down earl.
-
If there is anything I can do to help speed this up without the cost of my money I will. Time is not money in this case
-
Lol
Lol
-
-
hey stewcrew how did you get such a big pic on ur sig?
1984 BMW 528e - SETA and manual swapped! M50 to come!!!
1988 BMW 528e - Need parts?
1991 Chevy C1500 (mighty 350 with TBI and Wisconsin weight reduction package)
1996 Mazda Miata (SOLD!!!)
1996 BMW 325i (Donor car)
1998 Chevrolet Corvette (BEAST)
2001 Jeep Grand Cherokee (BROKEN)
-
hey stewcrew how did you get such a big pic on ur sig?
it's been there for forever
-
I made the purchase of a more period correct steering wheel yesterday=)
This means that my Grip Royal Grain with the horn button will be for sale shortly.Â
Obviously it is in brand new shape since the car has never been driven with it and I bought it brand new.Â
The new wheel is an Italvolanti that I found for an excellent price and it was one of the only wheels that I could find that I thought would flow well with the OEM+ vibe and is 350mm.Â
I will post a pic once it arrives and is installed so that I can make sure it looks as fitting as I am hoping.Â
Other than that I painted the proper side of my waterpump pulley last night since I painted the wrong side before=PÂ
Saturday should involve me installing my Ground Control RSMs, swaybar endlinks/bushings/brackets/hardware, and possibly starting to replace the wheel bearings.
-
I got my Ground Control rear shock mounts installed Saturday.
Here is the set of e46 m3 vert mounts that I replaced (less than a years worth of driving on them)
New versus old
Installed top plates
Then installed the shocks with the mounts
Also installed the new lower shock mounting bolts
After that I removed the rear sway bar to sandblast, repaint (not happy with how it looks from before), and then to prepare for the new bushings, brackets, end links, and hardware.
I noticed that the under side of my diff surface rusted through the rust reformer/paint and that my trailing arms are starting to do the same around the edges. I have been thinking of dropping the sub frame again to replace all of the bolts with new and this has me wanting to repaint it all again. I am not sure why said rust reformer would not have neutralized the rust like it looked like it had=/
-
After that I got the thermostat and housing installed with the gaskets, as well as the water pump pulley
The pile of scrap from the end of the day
After that I cruised up to Oshkosh for Collins BBQ=)
I now have an m44 crank pulley on the way and will have my new steering wheel and misc parts within the next month.
-
After that I removed the rear sway bar to sandblast, repaint (not happy with how it looks from before), and then to prepare for the new bushings, brackets, end links, and hardware.
I noticed that the under side of my diff surface rusted through the rust reformer/paint and that my trailing arms are starting to do the same around the edges. I have been thinking of dropping the sub frame again to replace all of the bolts with new and this has me wanting to repaint it all again. I am not sure why said rust reformer would not have neutralized the rust like it looked like it had=/
also
I spy an engagement ring
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login