Partiallypurplevisuallyviolet - Daytona M3 Build Thread

[Jdesign]

Are you back in business now?

[jc43089]

If the slave cylinder is installed right it can't just randomly blow the pin out.  The pin only comes out if you press the clutch pedal without the slave installed to the transmission.

[straight6pwr]

did you use a new clip?

make sure the fork was aligned properly? and make sure it wasnt worn through?

insert the clutch slave into the bellhousing at a straight angle? (that's what she said)

use the correct TOB?

[Jdesign]

straight6pwr said:

use the correct TOB?

Type Of Buttocks?

[Partiallypurple]

Jdesign said:

Are you back in business now?

Finishing it up today after work. Fingers crossed everything will go well

[Partiallypurple]

straight6pwr said:

did you use a new clip?

make sure the fork was aligned properly? and make sure it wasnt worn through?

insert the clutch slave into the bellhousing at a straight angle? (that's what she said)

use the correct TOB?

New clip, didn’t make sure the fork was aligned properly to be honest. Kind of stupid of myself. Didn’t have any problems with the last slave on my other e36 so I figure it was as easy as screwing on and making sure it’s tight. Going to make sure everything is perfect before I even look at that clutch pedal this time

[straight6pwr]

you can also test fit the slave before installing the transmission

[SteelBlue]

Partiallypurple said:

New clip, didn’t make sure the fork was aligned properly to be honest. Kind of stupid of myself. Didn’t have any problems with the last slave on my other e36 so I figure it was as easy as screwing on and making sure it’s tight. Going to make sure everything is perfect before I even look at that clutch pedal this time 

Correct me if I'm wrong, and I could be given this is a 1J, but when the fork is lined up correctly, the slave should sit off the bell housing a little as the dowel is pressing into the arm.

[KaiserRolls]

SteelBlue said:

Correct me if I'm wrong, and I could be given this is a 1J, but when the fork is lined up correctly, the slave should sit off the bell housing a little as the dowel is pressing into the arm.

Correct, it takes some pushing to get the slave to sit flush on the back of the trans

[Partiallypurple]

Well a whole new clutch setup later and throwout bearing and we are finally back up and running! Spent the day deep cleaning all the interior panels, deciding what was good enough to keep and what had to go! Also made a shift boot/cage for the CAE. Going to wrap it in alcanatara suede but the brushed aluminum isn’t bad till I park the car for winter soon. 

[jc43089]

Looks nice!

[Jdesign]

CAE is a life changer. are you planning on keeping it aluminum or will you darken that up a bit too?

[Partiallypurple]

Jdesign said:

CAE is a life changer. are you planning on keeping it aluminum or will you darken that up a bit too?

Which part? The part I made is getting wrapped, the shifter itself will stay as is with probably a white knob to match the letters on the seats and steering wheel. The aluminum should match the lips of the wheels

[Jdesign]

Partiallypurple said:

Which part? The part I made is getting wrapped, the shifter itself will stay as is with probably a white knob to match the letters on the seats and steering wheel. The aluminum should match the lips of the wheels 

The shaft. 🤭

It just doesn't seem like there is any other raw aluminum in the interior.

[Partiallypurple]

Jdesign said:

The shaft. 🤭

It just doesn't seem like there is any other raw aluminum in the interior. 

There is now! Just picked these up from a local tire shop they had sitting in the back in a box from the early 90’s. They used to be a MOMO distributor back in the day. Super neat score that’ll match the Recaro Momo Special and fit the period correct theme I’m going for. Also the cage is currently polished/cleared. I can’t find any other pictures or anything on these pedals

[YoungCR]

Really cool! How did those sit on a shelf for 20years??

[Partiallypurple]

YoungCR said:

Really cool! How did those sit on a shelf for 20years??

Sat in the back warehouse where no one could see them.

[Rekpoint]

Partiallypurple said:

There is now! Just picked these up from a local tire shop they had sitting in the back in a box from the early 90’s. They used to be a MOMO distributor back in the day. Super neat score that’ll match the Recaro Momo Special and fit the period correct theme I’m going for. Also the cage is currently polished/cleared. I can’t find any other pictures or anything on these pedals

This is pretty sick

[Jdesign]

WOAH.. that brings me back. 

So oddly, my very first car had a very similar set of those Circa 2004. The guy I bought it from was best friends with the owner of LINK motorsports back in the day. He got a bunch of free parts for the car that was sitting on the shelf. Sadly, this also meant the car was a pile of mismatched parts. Red seats, blue harnesses, red faded to brown steering wheel, etc. I ended up selling my pedals to some kid years ago, nowhere NEAR as clean as those. 

Congrats on your find!

[Partiallypurple]

Well not related to the Daytona. But picked up a Mauritiusbleu metallic 318i individual that has been sitting in a storage unit since 01’. Hasn’t seen daylight in 18 years. Originally ordered in Canada it spent its entire life in New Mexico. The thing is flawless underneath and has no rust. Excited to daily drive it and give it the love it needs. A deep cleaning, a buff, new fender and hood on the way! Was originally parked because the owner was leaving his marine base driving it to wisconsin home and got into a minor accident. Parked it, and here we are 18 years later.