Non-BMW Stuff on a BMW Forum
-
I like the look of those knobs, but they can be kind of pricey.
I do need to change up my current one though. I tried my Nardi on and it felt so sloppy because the knob is so light.
I am debating getting one of those IRP short shifter centering shifting deals as @suspenceful's feels like an bolt action shifter. Granted, these can be very pricey. But for how much you use it, I feel it's worth the price.
-
I like the look of those knobs, but they can be kind of pricey.
I do need to change up my current one though. I tried my Nardi on and it felt so sloppy because the knob is so light.
I am debating getting one of those IRP short shifter centering shifting deals as @suspenceful's feels like an bolt action shifter. Granted, these can be very pricey. But for how much you use it, I feel it's worth the price.
$114 for a shift knob is more than I wanted to pay, but I was willing to pay a little more something that worked well and that fit the era of the car.
I would say the extra height gives it a little more “slop”, but I haven’t had an issue with missing a gear.
-
Your knob looks great
-
Your knob looks great
That’s the nicest thing anyone has ever said about my knob. Thank you.
-
I know it always fees like an accomplishment when I have my kids in the BMW and am running errands. Makes the car’s existence feel more legitimate and justifiable
I totally agree. I wanted this to be my fun car, but I also did things in a way that we could use it for day trips and everyone would still be comfortable. It’s a really good feeling when my family is in it.
Ive also been dailying it for the past week while I give the wagon a tune up and repair the AWD. It’s been very pleasant.
-
Got a box of stuff for the next little project for the e30. I’m going to attempt to spray the trunk lid and bumper. If it turns out okay I will probably gradually work my way down the car panel by panel.
Non bmw but I replaced the module and pump that operates the awd on my XC70. Gave me a renewed appreciation for older cars. It was an expensive repair.
-
Im sure it’ll turn out ok on each panel. The color match/blending might be the issue.
I’ve seen your playhouse skills so I have full confidence in you
-
Im sure it’ll turn out ok on each panel. The color match/blending might be the issue.
I’ve seen your playhouse skills so I have full confidence in you
If I go beyond the trunk lid I would only paint sections where there is a seam so I’m not blending anything. Even if the color is slightly off between say a door and a fender, it will still look better than the paint that’s on it now.
-
Got a box of stuff for the next little project for the e30. I’m going to attempt to spray the trunk lid and bumper. If it turns out okay I will probably gradually work my way down the car panel by panel.
Non bmw but I replaced the module and pump that operates the awd on my XC70. Gave me a renewed appreciation for older cars. It was an expensive repair.
Looks the same as the P2R Haldex unit. Worst design ever! Why would it be designed so that you have to remove the driveshaft and input flange to get the 1/4" of clearance to remove the pump???? And why is the filter in such a difficult spot??? Also no drain plug for Haldex or the rear differential. I added 1/8" NPT drain plugs to both on mine when I had it. There is no way to properly remove all of the fluid with the suction method. Oh and the price for parts is insane. A new pump is over 300$ for that tiny little thing. Luckily mine failed open, probably due to the brushes being worn out but if it shorts then it will ruin the DEM and then you are out 400$ for that too. And the special fluid is 30$ / liter. I don't miss that car.
As for the painting, see how it goes with the spray cans but I am a novice and had good results painting some parts on my van after a deer accident with an old HVLP gun. The spray cans will be very expensive to do a large area with. Mine turned out good and it was Toyota Beige with metal flake which made it trickier than just a regular color. The metal flake takes practice to lay down evenly but even that I figured out pretty quick how to make it look right. I tested on a piece of cardboard to get the gun set up. That looks like the 2k clear coat in a can. Huge sticky mess on everything. Make sure to protect everything, the over spray goes everywhere. It is different than paint over spray, somehow it coats everything in the room.
-
Kind of like @jc43089 said, cans are expensive for areas larger than a trunk or smaller panel. If you want to not spend a lot, the Harbor Freight guns are good for one day of use. I.e. don't clean them and use them again. If you want some more confidence in the gun, you can get something decent for not a ton of money and will get a lot more even coating of paint with a proper gun over an aerosol.
Painting sucks, painting cars is worse.
-
Looks the same as the P2R Haldex unit. Worst design ever! Why would it be designed so that you have to remove the driveshaft and input flange to get the 1/4" of clearance to remove the pump???? And why is the filter in such a difficult spot??? Also no drain plug for Haldex or the rear differential. I added 1/8" NPT drain plugs to both on mine when I had it. There is no way to properly remove all of the fluid with the suction method. Oh and the price for parts is insane. A new pump is over 300$ for that tiny little thing. Luckily mine failed open, probably due to the brushes being worn out but if it shorts then it will ruin the DEM and then you are out 400$ for that too. And the special fluid is 30$ / liter. I don't miss that car.
They are the same. Since I replaced the pump all of the fluid was able to drain out, but the yes, the pump was $300 and the rebuilt DEM was $700. I have no knowledge of being able to purchase a DEM for $400 - since they are coded to your car.
And then you have to take it for a drive, top off the haldex fluid, and then suck out 40ml.
Once I get it cleaned up I will probably list it for sale and look for an 850 wagon.As for the painting, see how it goes with the spray cans but I am a novice and had good results painting some parts on my van after a deer accident with an old HVLP gun. The spray cans will be very expensive to do a large area with. Mine turned out good and it was Toyota Beige with metal flake which made it trickier than just a regular color. The metal flake takes practice to lay down evenly but even that I figured out pretty quick how to make it look right. I tested on a piece of cardboard to get the gun set up. That looks like the 2k clear coat in a can. Huge sticky mess on everything. Make sure to protect everything, the over spray goes everywhere. It is different than paint over spray, somehow it coats everything in the room.
It's not the 2k clear coat, it's the more basic one. I intend to close my garage door just enough to wedge my box fan under the door and then seal off the gap and run the fan to create negative pressure. I'm hoping most overspray gets sucked out then. I have a cheap HVLP gun, however, I have a relatively small air compressor that I bought primarily to run air nailers and fill up tires, so I don't know how it will work with a gun. But I might get some of their premixed paint to give it a shot.
Kind of like @jc43089 said, cans are expensive for areas larger than a trunk or smaller panel. If you want to not spend a lot, the Harbor Freight guns are good for one day of use. I.e. don't clean them and use them again. If you want some more confidence in the gun, you can get something decent for not a ton of money and will get a lot more even coating of paint with a proper gun over an aerosol.
Painting sucks, painting cars is worse.
I like the idea of painting, but it's not my favorite thing to do. The paint is in such bad shape that even if I get it to look OK, I'll be satisfied. But if this turns out fine, I'll also try their premixed paint assuming my air compressor can handle it.
-
I forgot the coding part, did you get it from Xemodex? I'm glad I didn't need to deal with that as mine was fine, my pump would run intermittently and it sounded weak when it was running, you can activate the pump with VIDA and watch the pump current draw and the output pressure. Do you have a VIDA/DICE setup? It is the most important thing for troubleshooting on a Volvo.
You need a decent air compressor for an HVLP gun but not a huge one. I think my little one I used for painting is around 2hp, 4.5 CFM at 90PSI. My compressor has a 4 gallon tank and then after the dryer was another 30 gallon tank. It was losing ground slowly as I painted but I gave it 30 seconds between parts to catch up and never had a problem. You need very dry air though, I made an ice powered air dryer that works really well for cheap, let me know if you want details on it. It worked so well that the dessicant final dryer never even had any color change.
I made a "booth" with tyvek wrap and had 3 box fans exhausting under the garage door and everything inside the booth had clear coat on it.
-
i also made a 'negative pressure paint booth' with a box fan inside a small room. it does not keep the paint off of surfaces as well as you think it might. it does help keep the cloud of paint from being super obnoxious and helps with exhausting the fumes. you should still be prepared to cover things you don't want to get speckled.
i also deployed that 2k clear for painting a bicycle frame once. the extra nastiness of the paint wasnt worth the hassle for the finish it created. i wouldnt use it again. YMMV
Dan
-
I forgot the coding part, did you get it from Xemodex? I'm glad I didn't need to deal with that as mine was fine, my pump would run intermittently and it sounded weak when it was running, you can activate the pump with VIDA and watch the pump current draw and the output pressure. Do you have a VIDA/DICE setup? It is the most important thing for troubleshooting on a Volvo.
Yeah, I have VADIS. I had sent it in to xemodex for them to rebuild it and they called back after running their tests and said "you need to replace the pump or the warranty will be void". Basically, your pump is also fucked. So, I did it all. Job was actually pretty simple, just so much money, and seems so unnecessary.
Mine failed by blowing the fuse for the AWD system in the trunk. Replaced the fuse and it blew it again instantly. Car had no communication with the DEM because it had no power (and couldn't power itself). But there was a laundry list of codes stored from it. But, drove it to work today and all appears to be well.
You need a decent air compressor for an HVLP gun but not a huge one. I think my little one I used for painting is around 2hp, 4.5 CFM at 90PSI. My compressor has a 4 gallon tank and then after the dryer was another 30 gallon tank.
I have an 8 gallon husky which is 4.8 scfm at 40psi which from what I can decipher is at the low end for a mid-grade hvlp gun to run efficiently, but it can be done.
. you should still be prepared to cover things you don't want to get speckled.
I will be moving stuff out of the garage that can be affected by odor (strollers) and will cover everything else. Going to get one of those rolls of plastic from Maynerds.
-
Save big money
-
I agree next time a harbor freight gun is the way to go. Buy 2
1 for primer and 1 for base/clear.
Naked Gun by Klean Strip to clean them out. They are good for a bunch of uses as long as they have been cleaned correctly.
People give the harbor freight guns shit all the time when in reality it usually isnt the gun. Its the painter.
Make sure you get an air regulator and an oil/water separator to prevent greasy air from getting into your paint.
This is for next time.
-
Lol. Now I wish I would have just gotten the premixed paint to use with an hvlp gun right away. Oh well.
I was skeptical if my compressor would work, but from everything I’m reading it should be fine. Maybe not ideal, but should work.
Now I want to spray the whole car. Maybe in spring.
-
4.8 cfm at 40PSI is not going to be enough. I think my gun spec is around 12 cfm at 25psi. Mine is about 4.5 @ 90PSI which is significantly more air than at 40PSI. Also the more storage you have the more of a buffer you have. I need to get my big compressor hooked up. It puts out 21cfm at 175PSI. It only runs about 50% duty even sandblasting.
I used Nason brand paint from my local parts store and I would use it again, good price and it sprayed nicely.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login