Lifted E30 V2

[B C]

its gonna run so nice I bet

[HipMF]

Am I the only one wondering how you're going to get the metal chips out of the pan? Wouldn't have been more convenient to do this while the subframe was out for spacer installation?

[Daggerty]

HipMF said:

Am I the only one wondering how you're going to get the metal chips out of the pan? Wouldn't have been more convenient to do this while the subframe was out for spacer installation?

Hey now, a few metal flakes never blew up an engine. I doubt it would suck any up and when it does the pump might blow but if not the filter will get um

[GunMetalGrey]

HipMF said:

Am I the only one wondering how you're going to get the metal chips out of the pan? Wouldn't have been more convenient to do this while the subframe was out for spacer installation?

Subframe wasn't out at any point during spacer stuff, but I can certainly drop the pan with ease now. 
Leaving the oil in the pan was actually beneficial to keeping chips controlled. The chips all piled up on the sides until the bit started going through, but once the bit went through the oil kept all of the chips right at the surface and in the hole. Turned out to be quite handy. I do intend to change the oil and flush the chips out a bit with extra oil through the hole I made. Should be a-okay. 

Speaking of subframes, it is really funny to walk around the car and see a massive air gap between the subframe and the oil pan. 

On to better things! 
I spent some time getting the motor and pump timed. I started from ground floor on the timing and set the crank, cam, and pump at their respective TDC's and then threw the timing belt back in. Spun it a few times and it looked good. 
Static timing the pump is amusing, as you unscrew a bolt in the back and thread in a dial indicator and zero it out on the largest value, rotate the crank to TDC, then read the value of timing advance, if the number isn't what it needs to be you rotate the pump in the brackets until the reading on the indicator is correct. 
Motor timing, check.

I then played the puzzle of fuel lines, which I thought would have been easier. They all fit together in one very specific way, so once I figured that out I took each one back out and cleaned it up a bit. Final result below!

Next step is to get fuel into everything and start bleeding the fuel system, which is a bit time consuming and can lead to headaches. Once again I want to make sure it runs before putting everything back together.
Don't worry, I'll remember to take the towels out of the intake ports... lol

[YoungCR]

looks great!

[SteelBlue]

Forgive my ignorance, but what is the large bulge on the valve cover for?

[Jdesign]

Thats a good question, I am now wondering the same thing!

[GunMetalGrey]

Tis a vacuum pump! 
Since a diesel engine doesn't create any vacuum in the intake, there needs to be a source for brakes. Many diesels use hydroboost (power steering pump) for brakes, as do e28's, even the gassers. Some run a vacuum pump on a belt, but this one has one that runs on a cam lobe on the main cam. 
Nifty stuff.

[B C]

Learning is fun

[HipMF]

GunMetalGrey said:

as do e28's, even the gassers.

Googling e28 gasser did not give the results I was hoping for. I might have to do something about that... that would confuse the hell out of people.

[GunMetalGrey]

@AsparagusMike showed up Friday and watched me try to get air out of my fuel system for about 5 hours, I'm sure it was amusing seeing it still not start. 

I went back Saturday and loosened the fuel outlet on the back of the pump for one injector and suddenly is was moving fuel (after raising the fuel cell above the pump). 
@HipMF sat and watched in amusement as I tried to get all the air out, while sucking in air bubbles and such, then tried to start it with no avail. I had vast amounts of homework to do so it had to be left for later. 

It turns out that it blows perfect smoke rings out of the exhaust most of the time so that was cool. 

Hopefully will have it running some night this week.

[Jdesign]

Post pics of smoke rings I wanna see!!!!

[GunMetalGrey]

I see my member title has changed. 
I approve of this change, and shall continue to ensure the most bro content possible. I do have something planned that will greatly increase my bro level.

[patsbimmer1]

[B C]

Is that the movie where Mater gets it up in the middle of the night?

[patsbimmer1]

snap said:

Is that the movie where Mater gets it up in the middle of the night?

Yea and then Sally let's Lightning come in her Cone.

[straight6pwr]

GunMetalGrey said:

I see my member title has changed. 
I approve of this change, and shall continue to ensure the most bro content possible. I do have something planned that will greatly increase my bro level. 

just watch out for donald glover and dave matthews CDs.

[SteelBlue]

GunMetalGrey said:

I see my member title has changed. 
I approve of this change, and shall continue to ensure the most bro content possible. I do have something planned that will greatly increase my bro level. 

Whips?

CB?

4 inch tips?

[GunMetalGrey]

SteelBlue said:

Whip?

There is also one of those laying around for it if the bro level is not over 9000.

[HipMF]

straight6pwr said:

just watch out for donald glover and dave matthews CDs.

Is this Dave Matthews?