E21 Project Thread - Part 2

[HipMF]

Just future proofing for the boost addiction. Not that it's a big deal to redo the lines later...

[Bassboy3313]

Yay!!! Fuel lines and mounting clips showed up today from Germany

Sent from my SM-G930R4 using Tapatalk

[KaiserRolls]

Bassboy3313 said:

Yay!!! Fuel lines and mounting clips showed up today from Germany

Sent from my SM-G930R4 using Tapatalk

I usually buy mine in packs of 100 at menards

I’m talking about zipties Dave

Zipties

Dave

[Bassboy3313]

Fucking cheap ass bender kinked the supply line while trying to copy the old one. Now what to do, what to do...

Sent from my SM-G930R4 using Tapatalk

[Jeff]

Jesus what bender did you use?? I have one if you need to barrow it

[YoungCR]

Thought the lines were pre bent?

[Bassboy3313]

I ended up being able to fix it after picking up a better bender. The return line was prebent, but the supply line was not. Not sure why bmw did this as they both have almost identical bends. I was able to save 10 out of the 12 mounting clip bushings, which is better than I expected. The screw broke off in the other 2 and there wasn't any way to get it out. Shouldn't be an issue tho. So I cleaned up the underbody surface while the lines were out and painted/underbody coated it all. I also painted the lines to help prevent corrosion starting. I should be able to get the lines back in this week and put the tanks back in.

Sent from my SM-G930R4 using Tapatalk

[Jdesign]

Sheesh. I thought you were going to have to order more uber rare OEM lines from deh Germanz again. Glad you make it work, now where are the pictures?

[Bassboy3313]

Got the lines installed finally. What a pita. Had to use some pretty MacGyver tricks to get them where they needed to be and clamped in. Now to replace all rubber lines, install tanks and hook new pump/filter up.

Sent from my SM-G930R4 using Tapatalk

[YoungCR]

The lines look fantastic though!

[Jdesign]

Worth it for sure!

[Bassboy3313]

Well I've been taking a break from the e21 for a drift bike project, bit decided to jump back into it today. Got the gas tanks installed with vent hoses connected, ran fuel hoses from top of tank to return line and to a new walbro external pump and e30 fuel filter. Just need to run fuel hose from hardlines to fuel rail and fpr up in engine bay.

Sent from my SM-G930R4 using Tapatalk

[B C]

Is that some dynamat type stuff on the floorpan?

[Bassboy3313]

Snap said:

Is that some dynamat type stuff on the floorpan?

Yup. Picked it up at home depot in the roofing section. Acts as sound deadening and anti rattle. I applied it to entire floor before laying carpet down since I removed all the stock sound deadening.

Sent from my SM-G930R4 using Tapatalk

[Bassboy3313]

She's alive once again. Finished up the fuel hoses to the rail and regulator and she fired right up. Some smoke coming from the new turbo manifold area. I'll have to run it more to see if it's just oil or paint burning off or something else.

Sent from my SM-G930R4 using Tapatalk

[Jdesign]

YASSSS!

[YoungCR]

Woot woot! Time for a burnout vid

[Jeff]

YoungCR said:

Woot woot! Time for a burnout vid [emoji6]

I second this motion!!!!

[Jdesign]

Jeff said:

I second this motion!!!!

Thirdssies this motion.

[Bassboy3313]

Figured I'd start on fitting the group 2 kit. Not much progress but it's something.

These fenders had a shit ton of glue holding them on from the factory. Craziness!!!

Got the new ones on that were already cut for flares.

Got the front valance switched out too and started fitting the grp2 front spoiler. Looks like I'll need to add a fiberglass lip to the top edge, so the rivnuts have something to grab. I also started installing the single headlight setup I made quite awhile ago. Having trouble getting them to turn on with the headlight switch. Must be a wiring issue.

And... totally forgot I paid for this guy over a month ago. Just got it today in the mail. Any guesses?