E21 Project Thread - Part 2
-
Is it an actual Evo? I remember a few weeks ago rob warned everyone about reps. But if it came from their store or it was used I'd have no worries
-
It is indeed a real evo3
Sent from my SM-G930R4 using Tapatalk
-
Wired up the EBC and radiator fan relay. Just need to run the control ground wire to megasquirt and connect the db15 connector. Then figure out the settings in tunerstudio for control.
I also had to drill and tap new holes in the shifter cup for the UUC evo3 shifter since previous owner stripped the holes out big time. Hopefully all my measuring and lining up works out and the holes are where they need to be. Will be installing tomorrow morning.
Sent from my SM-G930R4 using Tapatalk
-
Shifter is in with the TRM shift knob I got for free due to them sending it to me when I ordered a hard to find oem bolt and nut. Feels fantastic compared to stock shifter!!
Sent from my SM-G930R4 using Tapatalk
-
How tall is your knob
Heterosexually speaking
-
How tall is your knob
Heterosexually speaking
It's the 6" one. Like I said, they sent it to me by accident.
Sent from my SM-G930R4 using Tapatalk
-
Started working on the hood project. Since the fiberglass hood I got is just the skin with no support bracing, I decided to get creative. In order to get the hood in the correct position in order to fiberglass some bracing on underside, I decided to copy the curve of the original hood.
How I'm doing that is taking some 1/2" pvc, laying it across the top of original hood, heating it up with heat gun enough to "melt" it to the correct shape. Once cooled down it will act as a rigid structure that I will glue to top of fiberglass hood. This will hold the hood in the correct position while I fiberglass the structural bracing on underside. Once complete, the pvc can be removed and if done correctly, will be perfect fit to the car.
We shall see if my theory is correct or not, lol.
The pvc on leftt is completed. Heat gun took a crap on me, so I need a new one to complete the one on the right.
Sent from my SM-G930R4 using Tapatalk
-
Did some surgery to my megasquirt ecu today. Been wanting to have megasquirt control the cooling fan, but never knew how to get it working. After talking with Keith, the guy who made the unit, turned out to be easier than I thought.
Had to solder in 2 wires in order to have relay control from a spare pin on the db15. After doing that and buttoning the ecu back up, just had to run the ground wire from a 40A relay to the correct pin on db15 connector and tweak the settings in tunerstudio.
I am having one issue tho which I believe I found the culprit. With ignition off, the radiator fan will run constantly. With ignition on, it turns off unless engine temp is higher than allowed through MS. I then realized that I wired the relay to be constant power for both +12v pins. Which makes sense why the fan is running constantly when ignition is off. I'll have to run another switched source wire to the relay tomorrow morning to see if that solves it.
I also need to figure out the boost control settings since I got an error in tunerstudio when I turned it on with default settings.
Sent from my SM-G930R4 using Tapatalk
-
Started working on the hood project. Since the fiberglass hood I got is just the skin with no support bracing, I decided to get creative. In order to get the hood in the correct position in order to fiberglass some bracing on underside, I decided to copy the curve of the original hood.
How I'm doing that is taking some 1/2" pvc, laying it across the top of original hood, heating it up with heat gun enough to "melt" it to the correct shape. Once cooled down it will act as a rigid structure that I will glue to top of fiberglass hood. This will hold the hood in the correct position while I fiberglass the structural bracing on underside. Once complete, the pvc can be removed and if done correctly, will be perfect fit to the car.
We shall see if my theory is correct or not, lol.
The pvc on leftt is completed. Heat gun took a crap on me, so I need a new one to complete the one on the right.
Sent from my SM-G930R4 using Tapatalk
may i suggest gluing at least one pvc piece as a cross brace to prevent twisting between the front and back. looking at the picture, make the pvc look like an 'N'
Dan
-
Thanks for the suggestion. The pvc you see in pic is only being used as a temporary "form" in a sense. It will hold the flimsy fiberglass hood to the correct shape while I fiberglass bracing in on the underside. The fiberglass bracing will definitely have crossbars and such. Pretty much mimicking the shape of the structure from original hood. After that's done, this pvc will be removed.
Sent from my SM-G930R4 using Tapatalk
-
Also, changing the one pin on fan relay to a switched power source fixed the issue of fan running when ignition is off. Now to just figure out these boost control settings.
Sent from my SM-G930R4 using Tapatalk
-
motor swap again?
-
motor swap again?
Now wouldn't THAT be amazing!!! *drool*
Sent from my SM-G930R4 using Tapatalk
-
Got the braces done for the hood project. Hoping it works as it should to hold the hood in correct shape while I fiberglass the structure underneath.
Debating what to use to glue the pvc to top of hood. It has to be strong enough to hold hood to shape and also be able to be removed easily after structure is fiberglassed in underneath. Any suggestions?
I also grabbed a set of smoked turn signal lenses. They are for Euro signals, so the US housings require trimming to fit. As you can see.
Sent from my SM-G930R4 using Tapatalk
-
Well the pvc forms and hot glue seem to be working great!
The hot glue will remove nicely too when it gets to that part. I'm taking Dan's advice and will be putting one more pvc piece on diagonal to make an N shape. I should then be able to remove from car, flip it over and glass in the actual structure.
Sent from my SM-G930R4 using Tapatalk
-
Straight lines are hard
Sent from my SM-G930R4 using Tapatalk
-
So I got into my car this morning to do another tune run, push the start button (push button ignition) and I got absolutely nothing from starter. Everything gets power when I flip the ignition switch, but no cranking whatsoever from starter.
Battery is brand new, so that can't be the issue. All wiring I see is snug and tight. I have my start button wired up to the diagnostic port pins that go to starter and battery bus. It was the easiest way to do it at the time. I did disconnnect the wires and connected my remote test button to diag. port and still nothing. Haven't had any issues until now. Hell, it even started up just fine on monday.
Anybody have any ideas for me??
Sent from my SM-G930R4 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login