Doormans e30 325e
-
http://www.wibimmers.com/board/index.php?/topic/3401-new-member-from-south-of-the-border/#entry52155
Figured I'd drag this over here.
Previous info in the thread above.
Shifter rebuild parts from pelican arrived today.
I've seen a video diy on bav auto for an e36 and he broke the "bitch clip".
Should a grab a new one just incase?
I was gonna do the rebuild this weekend but I have to work Saturday night......stupid work!!
Too damn cold anyway.
My heater in the garage would barely make a dent.
-
I haven't broken one in several times of removal/installation but it could happen. It can be done without dropping the exhaust or driveshaft unless you have massive hands. I would recommend a small short flat screwdriver to get the clip rotated up so it can be pulled back. Might help to lower the back of the trans just a half inch or so. Always use jack stands.
-
If they have them at the dealer wouldn't hurt to grab one. I replaced mine just because I had a new one.
This was my thought as well.
Local dealer isn't too far and I get a CCA discount as well.
-
I haven't broken one in several times of removal/installation but it could happen. It can be done without dropping the exhaust or driveshaft unless you have massive hands. I would recommend a small short flat screwdriver to get the clip rotated up so it can be pulled back. Might help to lower the back of the trans just a half inch or so. Always use jack stands.
I saw a DIY where the guy used a hook type tool from harbor freight to pop off the clip.
Who needs an excuse to go to Harbor Freight!
-
I saw a DIY where the guy used a hook type tool from harbor freight to pop off the clip.
Who needs an excuse to go to Harbor Freight!
Yes that would work quite well. It can be hard to get started rotating because there is a barb that digs into the aluminum. A new clip would also be helpful just to look at while you are doing it blind to understand what you are doing.
-
Yes that would work quite well. It can be hard to get started rotating because there is a barb that digs into the aluminum. A new clip would also be helpful just to look at while you are doing it blind to understand what you are doing.
There's a GIF image on one of the forums showing how it's done. Makes perfect sense to me. Lots of blind fasteners/odd stuff in the door industry.
-
Cleaned out the garage over the weekend.
Both BMWs are now toasty warm!!!
Ordered this from the dealer today
Special order part......had to pay up front.....$6.00 including tax!!!
Weather for later this week/weekend is supposed to be warmer and work seems to be "calmer".
I hope to get her up on jack stands Friday night and tear into the shifter bushings Saturday.
Sent from my iPhone using Tapatalk
-
Hey Doorman. After you rebuild your shifter let me know if you might want to tackel mine for some $$. Mine is super sloppy. Or possibly install a short throw. Or if any other members have expierence with it and would possibly like the job.
-
Hey Doorman. After you rebuild your shifter let me know if you might want to tackel mine for some $$. Mine is super sloppy. Or possibly install a short throw. Or if any other members have expierence with it and would possibly like the job.
You're welcome to come and check/help out if you'd like!
I'll definitely post up results.
Currently defrosting wife's Honda Odyssey windshield washer reservoir.....damn women and their dollar store crap!
-
Where are you located?
-
Where are you located?
Southern burbs of chicago
-
Jeesh. Thats way to far for me to just come take a look and help out. Would love to tho.
-
Well.........
Got the e30 up on jack stands and started poking around underneath her.
It appears I have an early model sheet metal shift carrier and not the aluminum shift carrier.
Most of the parts in the bushing kit from pelican should work.
Anyone have any experience/tips in tightening up the bolts in the front of the carrier?
Doing some web searching now and back at it tomorrow.
-
Interesting. The bolts are loose? I have never worked on one of the early style like that.Sent from my potato phone
Yes.
There's a bolt thru a piece into the trans and a bolt thru the same piece into the carrier in 2 spots on the front of it.
-
Lots of reading last night and comparing parts.
Looks like I have the correct kit.
Dropped rear of exhaust, removed heat shield above exhaust and working on guibo bolts/nuts.
Hoping to remove nuts and slide drive shaft back and let is hang to get access. I marked guibo with some spray paint, all my reading says to reinstall in original orientation.
Gonna try to get the balancer mounted around the guibo off as well.
Back to work!!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login