ClassE 1989 325IS Build Thread
-
Your subframe is lowered and your diff is lowered quite a bit. That is bad news bears for your U joints and driveline angle.
Even the lowered subframe is not great
It's not a CV joint so it will throw some serious vibes if it is outside of its allowable range.
I still have the back half of a good shaft if you need it. -
Your subframe is lowered and your diff is lowered quite a bit. That is bad news bears for your U joints and driveline angle.
Even the lowered subframe is not great
It's not a CV joint so it will throw some serious vibes if it is outside of its allowable range.
I still have the back half of a good shaft if you need it.
I think the current plan is to swap the CSB and Giubo onto the original driveshaft - and bring it in to be balanced. If it balances out good it'll go back in... If not - I'll have to address then.
-
If your U joints are shot you will still get some clunking back there, the joints shouldn't have any play.
-
No play and there shouldn't be a lot 'sticky' spots when you move the joint around.
@DrLeadFoot
-
-
Dat m70 manifold though
YOU SEE NOTHING!!!
Not sure I'll be using that - might have a slight change of plans in mind for the intake manifold.... We'll see how the summer pans out.
-
Shift linkage is rebuilt and back in.... And it was a monumental PITA. Thankfully it was worth the headache because the shifter feels fantastic.
Electric fan is mounted and radiator mounting is done. Gotta figure out fan wiring and figure out what I'm gonna do for an upper rad hose.
Hopefully tonight I can yank those rear diff spacers and remove the no longer needed accessory crank pulley. I'm assuming I should get shorter bolts to replace the existing ones - or add washers?!? Will have to figure out tonight.
-
YOU SEE NOTHING!!!
Not sure I'll be using that - might have a slight change of plans in mind for the intake manifold.... We'll see how the summer pans out.
Budget = ITB's
-
Budget = ITB's
I can neither confirm nor deny anything.
-
I retract my previous statements - I did not install those diff spacers when I put the subframe bushing in (josh and I both thought we saw them up there - but went to pull them out last night and realized they weren't in there after all!)
Driveshaft is back in now, and got front studs in.... Just gotta get exhaust up, figure out elec fan wiring, torque axle nuts all around, and get an upper rad hose sourced/spliced.
Lots of detail work - but if things go smooth hopefully I'll be rolling tomorrow night?!?
-
My "Holy crap..." Moment of the evening though was when I was getting out from under the car and noticed the rear subframe bolts didn't have as much thread showing as I remembered. Threw a socket on them to check tightness.... And got another 4-5 turns out of them both!!!
They are now loctited.
-
It's truly pathetic how bad I am with wiring. Need to get an electric fan wired into car, and just can't wrap around how I am supposed to do this. Spent more then an hour looking at written directions - then the wiring in the car - and got nothing accomplished. So frustrating.
-
Are you keeping the oe aux fan? If not it's super easy. Replace the fan switch on the passenger side of the radiator with an 80/88c one (stock is 91/99c) from a 318, its plug and play. The hook the large wires that go to the oe fan to your new one.
Sent from my potato phone
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login