Chapter GMW | E30 LS1 (starting on post #1427)
-
Does anyone have a TDC flywheel locking pin? Or could make one?
Specs:
http://www.advrider.com/forums/attachment.php?attachmentid=219972&stc=1&d=1258414732
I will be making my own camshaft lock tool:
This is soo ghetto. hahaha. Why do this when you can go to concours and ask todd or burger to borrow them for the weekend or such. Not like they use them at the dealer everyday.
-
I'll do that! Timmy, you are always pulling through!!
@DrLeadFoot
-
I will be getting the VAC harmonic dampener. I tried to order it today but they didn't have time to process my order. I called twice. Great products, phones... not so much.
@DrLeadFoot
-
Got this over the weekend.
Is anyone familiar with timing the S52 that could swing by my house and make sure I have it correct? Willing to pay $$$
@DrLeadFoot
-
-
Just read the last 8 pages... life seems so much simpler without those 12 extra valves haha
-
The headache is worth the outcome! I got a taste of the power and it is addicting. The only car that got me was that fox body 5.0 that was turbocharged and probably built. He got the jump on me and still didn't pull more than one car on me. Soon. Soon.
@DrLeadFoot
-
-
Finally got into the garage.
With my JB racing flywheel there is no flywheel lock hole so I just need to keep an eye on the tdc mark.
The cam locking tool that I got was a little too narrow. So I'm going to watch that with my eye too. Sketch yes. I need to get this on the road.
Got the timing set up and just need to torque down the exhaust cam bolts while there is torque on the tensioner.
Then is is all down hill from there.
@DrLeadFoot
-
Then lets shoot photos
-
Got the lower cover on and torqued down. Black RTV'd everything and used the gaskets so hopefully no leaks.
VAC damper is on but I'm waiting to torque the NEW crank bolt.
Should finish the timing in the next 48 hours.
I've been busy...
Won the Milwaukee All City Mens Softball Tournament...
And got engaged!!!
@DrLeadFoot
-
Then lets shoot photos
-
Then lets shoot photos
So close yet so far.
Need to get all new block to engine mount bolts and torque & loctite them properly. Along with new motor mount bolts. The "stock" condor bolts have been beyond stripped.
Out with the old... in with new!!
New water heater too. $460 labor and parts. Jose the Plumber can do everything and some! 3 month warranty on his labor, insured, hard worker.
@DrLeadFoot
-
Finally made some good progress.
Made my cam tool.
Got the vanos all bolted up, rtv'd and torqued down.
Documenting these spark plugs. Kummrow put these in. I will replace them and make sure they are gapped to .021 and facing away from the intake.
To do list:
- Install oil pump.
- Oil pan.
- Valve cover.
- Torque subframe.
- Steering rack.
- Skid plate.
- Torque down transmission.
- New bolts for motor mounts, engine and subframe side.
- Random odds & ends to tighten up.
- Intake manifold & throttle body.
@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login