‘91 E30
-
Slave cylinder on the ZF is easy, plenty of room for socket/extension/ratchet
I am able to get the nuts off of it. But it seems like it's impossible to actually get it out or in without it pinching on the trans or the trans tunnel.
Only way I was able to get my broken one out was ripping the dowel out of it and just mashing it out. Maybe I'm taking the wrong approach, but I would be very interested to hear your technique as this is one of my last things to do.
My though was disconnecting the trans brace and loosening the motor mounts in hopes of being able to nudge it over just enough to get it in.
-
my vote is to just disconnect the top strut mounts and steering shaft, then lower the subframe 2 inches
and remove the skid plate
and disconnect heater hoses and drain coolant and remove the entire intake.
and the sway bar
and probably other things
i feel like a lot of stuff under there doesnt have 2 inches of compliance.
at that point you might as well pull the motor.
Dan
-
the extensions negate the impact effect though so hopefully it transmits enough shock. I had that issue during my manual swap and ended up just pulling the whole engine
did you have a 1400lb/ft impact wrench? the one mitchums has is no fricken joke.
Dan
-
I am able to get the nuts off of it. But it seems like it's impossible to actually get it out or in without it pinching on the trans or the trans tunnel.
Only way I was able to get my broken one out was ripping the dowel out of it and just mashing it out. Maybe I'm taking the wrong approach, but I would be very interested to hear your technique as this is one of my last things to do.
My though was disconnecting the trans brace and loosening the motor mounts in hopes of being able to nudge it over just enough to get it in.
I did not have trans bushings in at the time, but did not touch the solid mounts, I removed it with the line still attached. Just kind of maneuvered it out and let it hang
-
OH SHIT, you're that guy from those funny internet videos!
E91 328xi - F15 X5 40e - Hopes and dreams of eventually having a cool car
-
This weekend I got around to doing the detent service on the zf. Thanks to @m42b32 for the trans tools rental.
It’s pretty easy to do, most annoying part was when I had a snap ring fuck-off into a low earth orbit and bounce off the evo/Miata/garage door. Found it after a few minutes luckily.
-
Mobile is a real dick with putting text where I want without having to go in and edit the post so here’s the difference between the old 5th gear detent and the new 5th gear detent. (New detent on right)
-
Also they totally revised the pins on the top of the trans and added a coated bushing/sleeve instead of having the detent ride in a machined bore
-
None of my pins were frozen in the bores, but I figured I’d knock this out while the trans was out. A few definitely showed signs of wear though. Overall pretty easy to do and hoping it wasn’t pointless.
-
Started pulling the g260, got carried away
-
I didn’t remove the firewall insulation. Had I done this one simple trick we would not be seeing the engine out of the car.
Blame me for all the pain and suffering
New owners hate him!
Learn this one simple trick that ensures previous owners don’t get verbally assaulted on forums
-
Why did you end up pulling it?
Insulation was still present on trans tunnel, couldn’t get to the hardware, loosening mounts and tilting motor until it hit firewall was not giving me enough room
sans insulation and it could’ve stayed put
-
Might aswell throw a big turbo on it while its out.
A supercharger would be neat
-
-
Insulation was still present on trans tunnel, couldn’t get to the hardware, loosening mounts and tilting motor until it hit firewall was not giving me enough room
sans insulation and it could’ve stayed put
Guess that means mine will have to come out as well...
-
Guess that means mine will have to come out as well...
I ended up tilting and pulling the motor enough to where I could get to the hardware on the back of the block. Then slipped the trans off.
So it doesn’t necessarily need to come all the way out, but reinstalling with the engine dangling would be quite annoying
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login