'88 E30
-
If you want to run a manual rack but dont want the struggles and aesthetics of popeye, maybe consider a Z4 manual rack.
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
manual rack ftw!
-
I've ran it PS-less for a year and at a few events. It wasn't a "ftw" type of feeling.
Bottom line PS is nice to have
-
That's because a PS rack without the PS is no bueno. BUT a manual rack that is made to not have PS is ftw! The e21 has a manual rack and I love it.
-
Cams in the AM
-
Was your head that clean to begin with or did the shop clean it?
Machine shop hot tanked it
-
Was your head that clean to begin with or did the shop clean it?
He actually licked it clean, while saying something about "practice for upcoming wibimmer meets".
I think there is cause for concern.
-
Well with uncle bens help:
Cams are in and engine is timed, everything is torqued. Will be rechecking the ARPs after the first heat cycle
Still need to flush block as well
Rebuilt the vanos while he installed the cams (didn't take pics) was pretty easy. There was a decent amount of play before, not as much after. Hooray for no more marbles.
Installed new Stewart pump as well
Now it's just reinstalling exhaust & all other crap.
Realized I sold my intake elbow, so I can't really drive it around the rest of the year NA, so I'm forcing myself to finish the SC.
Looks like I'll have to figure out something for modifying the dipstick tube for a drain (or just tap the pan) as it interferes with the sc piping.
Probably need to buy a new tensioner as well. Also figure out belt routing.
Closer!
-
Hey, get this done so i can get a ride when i'm up next.
-
Hey, get this done so i can get a ride when i'm up next.
I'll try, been tough getting some free time as my folks are visiting this month from Nevada & spending time w/them is > e30
-
woah woah woah
someone said:
forcing myself to finish the SC.
you slipped that in there very non-nonchalant.
thats awesome!
Dan
-
Waiting on a temp sender (7/18 arrival) for the water temp gauge.
Also waiting on the ICV connector (to manifold) from reboot engineering (machined alum). After breaking 3 of the shit plastic ones and for the amount of times I'll most likely have to remove the intake manifold in this thing, I figured why not.
^thats all in the "parts yet to arrive" category
Stuff I'll need to figure out:
-oil drain from SC, tapping the pan annoys me
-intake elbow deal from SC to TB (current one has 2.7 million holes drilled into it) need to either replace it or slap something together
Need to get the 2nd O2 bung welded onto my exhaust for the wideband.
Need to install and wire all the gauges/senders/etc
Seatbelt situation
Extend fuel lines
Replace all the vac lines & install vacuum distribution block
There's more but I can't remember
-
Need to get the 2nd O2 bung welded onto my exhaust for the wideband.
Should be able to use the narrow band output on the AFR gauge
Saves you some hassle and another sensor -
KaiserRolls said:
Need to get the 2nd O2 bung welded onto my exhaust for the wideband.
Should be able to use the narrow band output on the AFR gauge
Saves you some hassle and another sensor
Don't you need to know values of the sensor or something odd like that.
@ snap and I discussed that but I can't remember the outcome
-
Don't you need to know values of the sensor or something odd like that.
@snap and I discussed that but I can't remember the outcome
I think he means use the simulated narrow band to ecu you just have to set high and low point for your wideband output, not all can do this. I believe it's 1.1 volts max, otherwise you will get a cel. I can find it if that is the route you are going.
-
Critical mission failure:
On Monday going to the local radiator shop to have them toss a 90° on
Also if you take the stock e36 upper hose and flip it 180° and trim off the side that originally connected to the rad, it should clear everything perfectly (obviously it will sit closer to the pulleys, couldn't get anymore bend with only one hand)
Ideally the hose will sit such as this
Depends how much room he needs with the TIG
I'm hoping that if it is semi close to the pulleys, that the solid engine and trans mounts will keep the whole shit show from piling into one another
Hoping to get some more piddly stuff finished up this week/weekend such as wiring/random hoses/dipstick drain perhaps.
Also most likely won't be able to run the intake tube they provide (hits ABS pump, angle doesn't work either) so I'm probably going to hop on silicone intakes and order up some crap and figure something out, already removed the drivers side hi beam [emoji849]
I suck at updates
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login