Build Thread?
-
This car looks so good.
I also need to contract Jake to do photos.
2011 E92 M3 6MT ZCP - ESS 625 supercharged
2007 Z4MR
2003 E39 M5
2002 E46 M3
2021 X5 40i -
That photo is so old
I owe you better photos than that.
-
Most annoying e30 job I have done to date. But it is done.
Upper U joint replaced and guibo changed out for a delrin counterpart.
Cleaned up the block, and found that it is also a can holder!
Dropped the head of to get decked and tanked, may not have needed it but peace of mind is well worth it!
I also tried on some seats, and am trying to figure out if they were too low or if they were okay. Picture for reference. Yes, it's grainy, the shop was quite dim.
I think they were a bit too low, as I had to use the door sill to get out and the wiper arm was a bit in the way lol.
Hoping to get the head back on this weekend!
-
Agree, steering joints suck. Is that from Condor?
It is! I am curious to see how the steering will feel with the slop out of the upper U joint and the lack of rubber in the middle!
@Earl I don't commit to anything that way when I don't show up it's no surprise!
I would like to take one of my E30's, but we all know how that goes. -
god damn I haven't had Rolling Rock since.....college. Fuck I feel old.
E30 picnic or bust IMO
2011 E92 M3 6MT ZCP - ESS 625 supercharged
2007 Z4MR
2003 E39 M5
2002 E46 M3
2021 X5 40i -
Yay progress
-
I could have sworn I followed through for checkout on ECS this Monday for a bunch of gaskets, but apparently I didn't. So that's lame.
I remembered yesterday that I need to do silly head torquing processes for this head gasket setup, and don't look forward to bolting the turbo down after putting the motor in and I'm debating waiting on putting the motor in. We shall see how much ambition I have!
I wish I would have dropped the head off at the machine shop earlier so I could be doing the silly torque process this week instead of starting it Saturday! -
Is it as silly as torquing it in a sequence and then having to wait a determined amount of time to do the next step?
Yep. It makes sense though, and I don't feel like risking another gasket combo to something that would be so stupid not to do.
At least this time I don't have to take the cams back out after the first heat cycle to torque the head bolts, the socket fits through m52 cam trays.
-
That's a plus lol. I believe you've done enough head gaskets for a lifetime. You and Snap could race to see if it is faster to do an M5X or an M20 headgasket haha
M20 for sure. You don't have to mess with vanos removal stuff.
Though the intake manifold removal is much easier.@Snap A gentleman's duel ? Loser is forced to put the winners engine in their car. Some big stakes there.
-
Grabbed the head on Friday and the guy that worked on it laughed at me for bringing it in because it was so flat already. Worth the money to know it's perfect and I didn't have to clean the old gasket off!
Got it timed, which I always find it satisfying when you do the timing and rotate it a couple times and check it again and it's still spot on.
Torquing the head still, and set some other things on it. Got the 85# injectors back in the rail and the manifold, and am waiting on some gaskets before I can bolt the turbo manifold back on.Slowly but surely going back together.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login