Lifted E30 V2
-
^this
I am tossing in the white flag on this engine. I have now replaced about everything and can only assume that when it froze something cracked and is not allowing the cooling system to function properly.
Next update will be the motor being changed again.
-
-
Well you might as well at least make the old motor go BANG first..... (please take videos of attempts for science)
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
Pulled the motor with the help of the guy that pulled it with me last time lol.
I took the stock single mass flywheel off and set it on the bench, I then went and grabbed my m52's flywheel with clutch and pressure plate on it.
The stock single mass (228mm) flywheel weighs more than my aluminum (240mm) flywheel WITH the pressure plate and clutch disc. Found that funny as the weight difference is quite noticeable.Motor didn't end up making it here this weekend so it looks like it will be a next weekend project!
-
Switched motors this weekend, and it runs but misses. Going to put in the injectors from the other motor and see if that's the issue as I already transferred the coil, cap, rotor, plug wires, and plugs.
-
That motor has been out for around4 years now, I do have video of when it last ran. Timing belt/water pump is "new" with no miles on it because I fried the dme shortly after and then decided to part the car and shell swap. It has around 168k on it and hadn't really been touched during the 3 years it was driven before part out.
-
That motor has been out for around4 years now, I do have video of when it last ran. Timing belt/water pump is "new" with no miles on it because I fried the dme shortly after and then decided to part the car and shell swap. It has around 168k on it and hadn't really been touched during the 3 years it was driven before part out.
I can't quite tell if this was informative or slightly defensive lol.
I have no concerns with the motor, as it runs well even though its consistently missing. I'm sure it's something simple otherwise it would sound a lot worse!
I look forward to trying to get the fuel rail out with the injectors, as it's quite the snug space! -
I can't quite tell if this was informative or slightly defensive lol.
I have no concerns with the motor, as it runs well even though its consistently missing. I'm sure it's something simple otherwise it would sound a lot worse!
I look forward to trying to get the fuel rail out with the injectors, as it's quite the snug space!Informative! Sorry haha
-
Did you check the cylinders with a temp gun?
You shut your mouth about the temp gun.
Yeah I totally did. It was cyl 2 and 6
-
Switched injectors out last night and it runs quite a bit better. Not perfect, but better.
I also put the cooling system back together on it.My plan? Connect the clutch hydraulics (so little space!) and go beat on it and see how it goes.
-
Man this car is annoying.
Can't drive it because it won't accelerate 90% of the time, just "stalls" and holds speed or slightly decelerates when you are on the gas. Occasionally it will pick up and accelerate for a second.
AFM? I'm running out of thoughts here. -
This is coming back in the shop!
Going to be replacing the engine harness as I have learned that E's have very volatile wiring. Hopefully that is the running issue I have been having!
-
Got this rolled into the shop Friday night, and got back at it! I was going to swap out wiring harnesses because I picked up a harness from another car, but after pulling the old one out and putting the new one in I realized all that was doing was adding more variables to the equation, and that's not what I needed! I put the old harness back in after cleaning up the contacts and grounds and figured I would start at square one. To my surprise it ran like it always used to, poorly, but running. I was quite excited!
I swapped in a set of projectors up front, and with the help of Mr. Mike got the relays jumped around so that I can run low beams, high beams, and the "offroad lights" which are wired up to the existing fog-light circuitry. I just need to get pigtails to connect to the 9005/9006 bulbs.
My most immediate goals are to level the car out (spacing the front subframe down 1.5") and to get some rear flares figured out.
The front subframe work is going to be an amusing one, as I will be keeping the motor in the same position relative to the chassis. After doing that I will start on a new skid plate and bash bar.
The ditches are trembling already...
-
I have a sudden urge to build a bull bar for my E36. This thing is so awesome, is this going to be your winter beater if you get it sorted?
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
I have a sudden urge to build a bull bar for my E36. This thing is so awesome, is this going to be your winter beater if you get it sorted?
I may drive it frequently, but I don't think it will see daily duty.
If I wanted to daily it I would need to work on the blower motor situation, as it only works on high, and sounds terrible while doing it. -
I just need to get pigtails to connect to the 9005/9006 bulbs.
I may have some of these, I'll check tonight.
Why didn't you swap the harness and start the car (without changing anything else)? If the car ran better, it was your problem. If not, you could've then swapped back to the old harness. Either way - nice to see you working on this again.
Has 'BEN PLS' been etched into the windshield glass?
-
I may have some of these, I'll check tonight.
Why didn't you swap the harness and start the car (without changing anything else)? If the car ran better, it was your problem. If not, you could've then swapped back to the old harness. Either way - nice to see you working on this again.
Has 'BEN PLS' been etched into the windshield glass?
I was wondering if those were the right plugs and forgot to ask you about it. If you wanna check that would be cool.
The "new" harness had a square c101, and the chassis is a round c101, and the control style is very different between the two so converting it isn't super fun. There is a longer story to it, but not worth typing.
Yep, that's etched into the glass now lol
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login