1JZ E30 Vert Build Thread with Pastry filled wheels

[Earl]

They're super simple to remove and swap out. You just need a very small flat head screwdriver to remove the two set screws holding it in. They're covered in wax. 

I removed the column bolts using a hammer and chisel. The head is soft enough where you can pound into it at and angle and break them free. They aren't all that tight.

[Jdesign]

Earl said:

They're super simple to remove and swap out. You just need a very small flat head screwdriver to remove the two set screws holding it in. They're covered in wax. 

I removed the column bolts using a hammer and chisel. The head is soft enough where you can pound into it at and angle and break them free. They aren't all that tight. 

Set screws and wax. Wut?

[Earl]

Nevermind, yours just clip on lol. Didn't realize the e36 was was different.

[The Full Banana]

Just remember to replace those shear bolts with some weaker hardware (grade 8.8 or so). Typically those bolts are designed to shear in a significant collision.

[Jdesign]

The Full Banana said:

Just remember to replace those shear bolts with some weaker hardware (grade 8.8 or so). Typically those bolts are designed to shear in a significant collision. 

You do remember this is an over powered convertible with no roll over protection at all right? Pretty sure if I hit anything hard enough to move the column, I will be ejected from the car before anything else.

[Earl]

You can already assume what I replaced mine with...

[Jdesign]

Earl said:

You can already assume what I replaced mine with...

Diamond plated titanium that was sand cast using the eye crustys of orphans then hand carved by Jesus himself using only tookpicks?

[Jdesign]

I need some opinions. I desperately need to get a turbo blanket, should I get a chrome one or a Black satin one..

Here is a pic of how the engine bay looks at the moment. The battery will be soon moved to the trunk.

[B C]

Black blanket

[wasnt m3]

Black

[YoungCR]

Once you go black...

[Earl]

Black

[Bassboy3313]

I have one for you if you want it. Brand new, never installed

Sent from my SM-G930R4 using Tapatalk

[patsbimmer1]

Black

[Jdesign]

Bassboy3313 said:

I have one for you if you want it. Brand new, never installed

Sent from my SM-G930R4 using Tapatalk

Good deal. Maybe when the tools come in I can scoop this from you. The vote is certainly in favor of a black blanket.

[Bassboy3313]

Sure thing!

[Jdesign]

Finally started cranking away at this again. I preregistered For Euro District so I would have a hard deadline to  push myself. As of the last two nights, I have made brackets to relocate and install my new power steering reservoir, and relocated my fuel pressure regulator under the intake manifold. My goal is to remove everything I can from the chassis in the engine bay, so that when I shave the bay, I will have a lot less work.

Although I fabricated a new bracket and moved the PS reservoir, I decided that at the end of the season when I do respray the bay, I am going to run a Z4 manual steering rack to help reduce some of the clutter in my engine bay. They are cheap and from what I have read, they have great feel and response.  I started looking into running a electric pump system or an electric rack as well, but cost, and clutter changed my mind there.

Besides all of that, I also modified the radiator brackets and made new intercooler brackets so that I could add 3mm between them providing more room for the Spal fan that I bought from @Snap 

I failed to take pictures of pretty much everything besides the PS reservoir as I was "IN THE ZONE" crannking on shit in the weeee hours of the morning. I will provide some more pictures later on when I button everything up.

[Jdesign]

I finished relocating both the PS reservoir and the FPR and I am quite happy with the result. I no longer have anything besides the fuse box mounted to the engine bay of the car. I am a little worried about the new location of my fuel line as it is a few mm away from the main power wire going to my starter. I think I am going to build some type of plastic cover to keep the two divided "just in case." But other that that I was able to clean everything up and hopefully this winder I can shave and paint the engine bay.

I also installed this nice Turbo blanket I got from @Bassboy3313 and it will really help keep the heat down and it looks much better than the rusty hot side.

[Jdesign]

I realized I didn't post any pictures of the complete engine bay in awhile. I accidentally spilled some chrome polish on the ground last night cleaning some wheels I have so I used it to clean some of the metal parts in the engine bay and snapped some pics quick.

Also, I am on the look out for some 17" staggered German Eclair wheels. If you have any leads, please let me know.

[KaiserRolls]

What wheels are on it in those most recent pics?