E21 Project Thread - Part 2
-
Use a screw driver to jump the posts.
Build is looking great!!
Sent from my SM-G935V using Tapatalk
@DrLeadFoot
-
Use a screw driver to jump the posts.
Build is looking great!!
Sent from my SM-G935V using Tapatalk
I am wary of that method on EFI equipped cars
I have heard horror stories of fusible links and ecus being fried from accidentally bumping the starter terminals with tools
-
Yeah. I wouldn't want to mess anything up further
Sent from my SM-G930R4 using Tapatalk
-
DrLeadFoot said:
Use a screw driver to jump the posts. Build is looking great!!
Sent from my SM-G935V using Tapatalk
I am wary of that method on EFI equipped cars
I have heard horror stories of fusible links and ecus being fried from accidentally bumping the starter terminals with tools
Is this why none of my cars work? Lol
Sent from my SM-G935V using Tapatalk
@DrLeadFoot
-
Well, after letting it sit for a day and the battery on a charger just for good measure, I went out there to try again. Tried to start it like normal and nothing still. Took my multimeter and checked that the main power wire going to starter had same voltage as battery, it did. I then hooked up my remote tester switch to the diag. port to test the ignition wire on the starter for 12V. Starter started cranking, didn't know car was in gear, ran over my foot, ouch!! Took it out of gear, hooked the push button back up to the diag. port like I usually have it, went inside cabin to start car, fired up no problem.
So my conclusion is I am either looking at a starter that is starting to go out or the wiring at the diag. port is being finicky and I should find a new way to wire up my push button start. Thoughts?
-
I got one with the sedan project, so maybe ill get that one tested and see if its usable. If so, I could swap it into the e21 and get that one rebuilt for the sedan.
-
Turns out the wiring connection on the starter from the sedan is completely broken. So looks like I'm in need of 2 starters now.
On a side note. Made a front strut brace yesterday.
Sent from my SM-G930R4 using Tapatalk
-
Question for you engineers.
When the strut brace is bolted in like that, couldn't the towers still move? I'm sure it's negligible, just curious.
The IE bar I have is solid from tower to tower fwiw
-
I was thinking of just welding it solid, but would be nervous about it never coming off the strut studs again, lol. It's already a tight squeeze onto the studs for the plates without the bar attached to them.
Sent from my SM-G930R4 using Tapatalk
-
I was thinking of just welding it solid, but would be nervous about it never coming off the strut studs again, lol. It's already a tight squeeze onto the studs for the plates without the bar attached to them.
Sent from my SM-G930R4 using Tapatalk
It sometimes helps with install if I jack the car up from the middle of the front subframe and let everything hang lol
-
I believe it may be the push button itself. Hooked remote button to diag port, it cranked. Hooked push button up to diag port, it cranked too. Pushed it again and nothing. Hooked remote button to diag port and it cranks
Sent from my SM-G930R4 using Tapatalk
-
Thanks to Kyle's shop mate Connor, I'll be picking up my new modified rear subframe hopefully this week.
Sent from my SM-G930R4 using Tapatalk
-
Only a few guys I know have done it this way. Others have used the entire e30 subframe and just weld the e21 mounts to ends. That changed the offset and spacing tho. Same with using entire e28 subframe which others have done too.
Sent from my SM-G930R4 using Tapatalk
-
All about the rare parts up in here
-
Yanked the starter out and got it tested at orielly. It's shit!! Grabbed a spare one and it tested good. I'll be throwing the good one in tomorrow and seeing what happens.
Sent from my SM-G930R4 using Tapatalk
-
Also, got a dead pedal from andy. Thanks again!
Sent from my SM-G930R4 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login