Chapter GMW | E30 LS1 (starting on post #1427)
-
I don't think I need to register. But I do have a sticker guy...
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
i can't wait to see this car in person and bother you for a ride in it
-
i can't wait to see this car in person and bother you for a ride in it
I got you! Haha. I can't wait to drive!!
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Oil leak should be gone soon.
Picked these up too.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Okay so I have a coolant leak coming from the thermostat housing. I fired it up after charging the battery and it wasn't leaking when cold after I snugged up the bolts. I'll drive it down to Billy's shop and have the oil changed then see if it is still leaking. If not, Late Model Throttle here I come!
@DrLeadFoot
-
It might be worth it just to see me get nervous as the dickens.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
9:00AM this Friday I'll be on the dyno at Late Model Throttle!! #itbetternotsnow
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
I'll get the gopro all set up.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
A very safe and strong 442whp. Not too happy but there is room for improvement and my A/F is consistent across the rpms which was my main goal with this dyno run. It looks like the TRM tune is in the 11-12s and will be safe to crank up the boost. My 1st dyno run I was below 10s due to vacuum leaks so this is a good thing.
I'm at 13psi. What do you guys think I should do to up the boost? Spring by spring and inch my way up or get a boost controller? Taking the wastegate out is a pain in the butt.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
-
440whp? Yea I would be a bit disappointed. Use a wastegate spring that's the lowest boost you want and use an electric boost controller on top of that for mad boostages. Aren't you running a 40r? Man I'm not that impressed. Turn up the boost and wake it up! You aren't even getting into the good part
This thing is a beast and I can't wait to see it in person!
sk8 or die
-
AFRs are nice and smooth, assuming the dyno doesnt have a crazy smoothing factor in place.
Do you have a compressor map for your turbo? otherwise what are the specs and I will try to find one
I have one a couple of pages back.
440whp? Yea I would be a bit disappointed. Use a wastegate spring that's the lowest boost you want and use an electric boost controller on top of that for mad boostages. Aren't you running a 40r? Man I'm not that impressed. Turn up the boost and wake it up! You aren't even getting into the good part
This thing is a beast and I can't wait to see it in person!I will turn it up for sure. I might wait until this weather warms up. There are times that I spin in 5th gear with the cold and salt on the road.
@DrLeadFoot
-
I'm not too good with dyno charts yet but aren't the HP and Torque lines supposed to intersect at a consistent spot at a lower rpm?
@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login