Chapter GMW | E30 LS1 (starting on post #1427)
-
check the compressor map. I know absolutely nothing about turbos but, check the compressor map.
I think we are in the same boat.
Here is the map for my turbo. This is a foreign language for me. HELP!
@DrLeadFoot
-
Looks like 2 Bar (29psi) would be my optimum boost for the turbo? That's 14psi more than I'm at now.
Oh god if this is right this will be crazy!!
@DrLeadFoot
-
I found this on you tube and this guy states you should consult the compressor map when choosing a turbo for you car. Anyway, I watched it and this guy knows what he is talking about.
http://www.youtube.com/watch?v=0Lv4yjiuJSU
Hope this helps
Mike
-
I found this on you tube and this guy states you should consult the compressor map when choosing a turbo for you car. Anyway, I watched it and this guy knows what he is talking about.
http://www.youtube.com/watch?v=0Lv4yjiuJSU
Hope this helps
Mike
That video was a great help. Todd, TCD, picked out the perfect turbo for what I wanted to do with the car it looks like! (I never doubted him!)
I'm thinking start with a 20-24psi spring in the wastegate and see how that works with the setup.
I emailed TRM to talk to them about fine tuning the tune. I would like to get it dyno'd at the high boost to get the air/fuel ratios documented and have them take it from there.
@DrLeadFoot
-
This is the type of attention I want to get with my dirty.
@DrLeadFoot
-
On compressor maps, the y-axis is the pressure ratio which is (intended boost pressure + 14.7psi)/14.7psi. so a pressure ratio of 2 equates to ~15psi boost pressure and a pressure ratio of 3 would be ~30psi etc.
On the x-axis, the target horsepower can be approximated by multiplying the flowrate in lb/min by 10. so 40lb/min being about 400whp. You want to land in the middle of the highest efficiency island.
TCD or anyone that isnt a total noob with turbos, please correct me and expound, I am here to learn.
-
On compressor maps, the y-axis is the pressure ratio which is (intended boost pressure + 14.7psi)/14.7psi. so a pressure ratio of 2 equates to ~15psi boost pressure and a pressure ratio of 3 would be ~30psi etc.
On the x-axis, the target horsepower can be approximated by multiplying the flowrate in lb/min by 10. so 40lb/min being about 400whp. You want to land in the middle of the highest efficiency island.
TCD or anyone that isnt a total noob with turbos, please correct me and expound, I am here to learn.
I was not calculating my pressure ratio correctly. 20psi would put me at 2.3 PR and that puts me right in the honey hole for the turbo! Well, maybe I guess.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Under the blankets trying to stay warm.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Just got these little guys for the trans. mounts. Now to order up some motivation.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Pull the trigger! Spring will be here sooner than we know it!
@DrLeadFoot
-
say goodbye to your teeth
Actually let me know how the vibration is. Better yet, I need a ride when they are installed.
As for motivation. Get some warm clothes on, Get the jack out, put a stand on one side, Get your 12 or 13mm wrenches out, support the trans with the jack, replace them, and be done with it in under 15 minutes.
I dare you.
-
say goodbye to your teeth
Actually let me know how the vibration is. Better yet, I need a ride when they are installed.
As for motivation. Get some warm clothes on, Get the jack out, put a stand on one side, Get your 12 or 13mm wrenches out, support the trans with the jack, replace them, and be done with it in under 15 minutes.
I dare you.
Maybe tomorrow. Maybe!
I got my charger for the gopro and can't wait to get some footage.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
YES! please post up lots of car videoss
This snow needs to go somewhere. With this cold and salt on the roads there will be Boat loads of wheel spin.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
You are driving that thing in the salt???
Not daily as of now. Here and there hell yeah! I can't let her get stiff in the garage! Gotta stretch her out!
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
M50) said:
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login