Chapter GMW | E30 LS1 (starting on post #1427)
-
-
-
I'm not sure if it was mentioned, but what kind of lip/splitter is that? I really like the look
I got it off a dude on r3vlimited. $78 if I remember correctly.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
I got it off a dude on r3vlimited. $78 if I remember correctly.
Sent from my SCH-I535 using Tapatalk
Thanks!
-
i am perfectly alright with this thread becoming a pictures-only thread of your car.
-
i am perfectly alright with this thread becoming a pictures-only thread of your car.
I'll let them do the talking. Haha
Getting in the garage soon. Update coming.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
I did a practice tap on my old valve cover and it turned out to be pretty easy and not nerve racking. I was nervous about how much metal would be left after the tapping but I think we'll be good!
I also scuffed up my rain rails to prep them for painting.
This is what Rat has been up to. Installing a $5000 inverter from a yacht into the barn that he got for free.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Update: Tuesday the e30 will go on jack-stands as soon as I get the new passenger caliper and rear brakes on the M3.
E30 to do list:
-I think I have sourced a drive-shaft that I will install.
-My PLX wideband brain just arrived back from warranty work. Throwing that in.
-Oil pressure sensor back light and signal wire.
-CCV
-Pull valve cover
-Tap
-Die grind port for more flow.
-Change trans fluid
-Top off diff fluid and RTV seal speed sensor.
-RTV seal ICV connector and brace hoses underneath intake manifold somehow.
-Replace Wilwood rotors and front pads.
-Bleed front brakes.
-Move BOV to brake booster vacuum. Going to T into that.
-Install fuel pressure regulator.
And that's it!!
@DrLeadFoot
-
I got the rack on and scooped up my old exhaust.
Go Pack Go!!!
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Heat cracks.
Time to port and tap!
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Load fine for me.
Nice car OP.
Thanks!
Rotors disassembled. Prepared for painting.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Time me.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Doing work.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
Did I hear right that you had Kumhoe did your engine? If i would of known that I would have done it for you.
?? Kummrow put the head/timing belt on.
Sent from my SCH-I535 using Tapatalk
@DrLeadFoot
-
?? Kummrow put the head/timing belt on.
Sent from my SCH-I535 using Tapatalk
s52 doesnt have a timing belt. haha. No i heard they put the motor together like block, crank, rods, pistons. etc. or did you have the machine shop do all that?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login