E30 M50 tear down kinda thing
-
Next was to make small "L" brackets, since the metal of both the car and the core support are fairly flimsy, I wanted to make sure it would be safe.
Checking fitment
Welded together. You will need to make two of these, one for each side.
Then just a square welded to the tabs for the lower section.
I kinda forgot to take a couple pictures for the next few steps because I was excited to get done, but theyre pretty straight forward. I used a 3/8" drill bit, and ran to napa to get nuts and bolts the fit snug in the drilled holes. With the holes drilled, I tightened them down as if I were actually putting the core support on, and welded the nut to the fender support (I guess is what you would call it?). Be very very careful doing this! The metal is super thin and its easy to melt right through it!
The next part was the trickiest. Remove you bumper shock if you havent already (13mm bolts), and tighten down your nut and bolt. Hopefully you will have fairly clean metal, which I was lucky enough to have. But you need to very carefully blind weld the nut inside the bumper shock housing. I took a lot of time to make sure I didnt get any metal on the bolt, because if you do, youre screwed lol. Here you can see both bolts screwed into the nuts with the core support removed.
You do that for both sides, and thats it! You have just made your new core support removable whenever you want!
Any questions/comments/concerns are welcome. This was a fun project and Im happy with the outcome
-
Brian said:
Good write up! How fast/easily removable is the front core support? I'm thinking of doing one for my E28, but I'd do mine differently.
With nothing in the car at all how it is now, maybe 2 minutes to get it off. Getting it back in is a little tricky because it has to be lined up perfect. I wish I went with a bigger drill bit for the holes but oh well, it works. I can take it off and put it back in within 5 minutes total. Im already excited for the amount of time its going to save putting the motor back in or when it comes out next lol.
-
Rowleym said:
How did you take it out in the first place? Just drill it out? I'm just about to take it out.
The old core support? I cut it right in half at first to pull my motor. The only thing holding the top sections in are the tack welds. Like I said in the post I'm not exactly sure where the tack welds are on the part that's around the bumper shock towers because mine was so rusted. But I know there's a couple thick welds on the outside of it. Feel free to text me in you want to send me pictures or have any questions! That way ill get it right away instead of checking here lol: 262-349-6277.
-
how many bolts hold your core support on? how many welds held the original in place?
a small front end collision could end up smashing your motor instead of the intended bumper/core support if its not held on tightly.
Dan
-
straight6pwr said:
how many bolts hold your core support on? how many welds held the original in place?
a small front end collision could end up smashing your motor instead of the intended bumper/core support if its not held on tightly.
A total of 4 bolts right now along with my welds on the brackets for support. Ill be adding 2 more bolts up top and 2 more on the bottom. Originally, there were 10 very small tack welds on top at each side, and I believe 2 welds on the lower bumper shock housing area.
After seeing how flimsy the oem metal of the old core support was, along with how flimsy the metal of the inner fender wall was, Im not convinced the stock support would have held up very well at all. You can pretty much use your hands to bend the entire from clip of the car in.
A front end collision would have to be hard enough to push the bumper shocks in, push the housings back at least 3 inches, and then hit the core support. I think it would have to be a pretty hard to to push the shock housings back that far, but who knows. I honestly feel much safer with the new set up compared to the old one.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login