Non-BMW Stuff on a BMW Forum
-
Awesome, that will be a good setup. It will have no trouble running impacts, die grinders etc all day. The right tools sure speeds up projects.
Any benefit to using pipe VS hose to hook the two tanks together? Obviously using some short sections of hose and fittings would be much easier.
-
Dan
-
This is the building blocks for additional e30 content.
Dan
-
Any benefit to using pipe VS hose to hook the two tanks together? Obviously using some short sections of hose and fittings would be much easier.
You could, I use hose because it is portable and easily reconfigured. I usually use a pretty short hose between the compressor and extra tank, it flows pretty fast even with a regular 3/8" hose that is 25' long. I like to fill the portable tank and then unhook the hose and drain the compressor. Then I can use the tank on wheels for airing up tires and little things until the pressure is too low and it needs filling again. I would recommend thread sealant like Rectorseal 5 to make a perfectly leak free system. Thread tape can be ok but sometimes leaks. You can get a jar for a couple bucks at my store.
-
You could, I use hose because it is portable and easily reconfigured. I usually use a pretty short hose between the compressor and extra tank, it flows pretty fast even with a regular 3/8" hose that is 25' long. I like to fill the portable tank and then unhook the hose and drain the compressor. Then I can use the tank on wheels for airing up tires and little things until the pressure is too low and it needs filling again. I would recommend thread sealant like Rectorseal 5 to make a perfectly leak free system. Thread tape can be ok but sometimes leaks. You can get a jar for a couple bucks at my store.
I’ll use regular hose. I’m going to build a rack that will stack the 2nd tank on top of the compressor, so the hose will only be a couple feet connecting the two.
First tank acquired though!
-
You will want at lease a short section of flexible. The aircompressor vibrates when running....a lot, the expansion tank wont. The vibration load on the connection, if all solid, will cause something to crack at some point.
That’s a really good point. I didn’t think of that. I’ll use regular compressor hose since the distance will be so short.
-
#wagonlife
those tie-down rails are awesome. thats volvo right?
Dan
-
#wagonlife
those tie-down rails are awesome. thats volvo right?
They really are. I use them pretty regularly. And yes, ‘08 Volvo XC70.
-
How about some e30 content?
All cleaned up for Road America tomorrow.
Great weather for being at the track. One of the few events I didn’t make it to this year. Hopefully you got to see the F1 cars run. Judd V10s
️ -
It was a lot of fun and my girls enjoyed it which is always awesome.
Tonight I got the air compressor hooked up. Not super thrilled with the overall look of it but it will be fine until I redo the garage next year.
I still need to do some hose management, so please ignore the crazy hoses.
-
Been driving the car to work once in a while and I've noticed that the oil pressure light stays on for a couple seconds on cold starts. I'm going to get a new oil pressure sensor, but I'm just curious what people's thoughts are? It didn't always do this. I remember it turning of instantly - I think even with this engine when I first got it back in.
-
Been driving the car to work once in a while and I've noticed that the oil pressure light stays on for a couple seconds on cold starts. I'm going to get a new oil pressure sensor, but I'm just curious what people's thoughts are? It didn't always do this. I remember it turning of instantly - I think even with this engine when I first got it back in.
At least for the e36 its actually in the owners manual that the oil pressure light is supposed to be on for 1-3 seconds after startup.
-
If you’re worried slap an aftermarket gauge in it for some redundancy
-
If you’re worried slap an aftermarket gauge in it for some redundancy
I looked into this and I think I’ll add an oil pressure gauge.
Now I need to decide if I should just go with an oil pressure gauge and do a single gauge pod in the vent or go with three gauges and do the ash tray gauge mount. Probably oil pressure, oil temp, and something else. But that seems like overkill in a stock car.
-
I looked into this and I think I’ll add an oil pressure gauge.
Now I need to decide if I should just go with an oil pressure gauge and do a single gauge pod in the vent or go with three gauges and do the ash tray gauge mount. Probably oil pressure, oil temp, and something else. But that seems like overkill in a stock car.
Overkill? Is that a thing? Anyway, coolant temp is always nice, the stock gauge is all but useless with the large buffered spot in the middle. If you add an oil pressure gauge use a T so you keep the idiot light. A gauge is not eye catching enough unless it has some kind of programmable limit with a warning light. Also depending on the sending unit size/weight I usually remote mount them so the large sending unit isn't hanging from a vibrating engine by a 1/8npt nipple.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login