new to me, 98 M3
-
Hey all,
So working on this right now tonight. I followed the steps above (cam locks, backed off torx bolts, tension on chain). I wanted to check chain movement before uninstalling vanos just to see where it was at. Applying pressure and activating the solenoid the chain didn't budge. You can hear the vanos make a blurping noise and the cylinder with the gear moves in and out just a little bit. Appears the solenoid is fine as it clearly does something when voltage is applied to it.
So, figured it was installed wrong, uninstalled and re-installed. Same thing. I'm very careful to make sure I'm catching the 1st possible gear.
I'm surprised that 60 psi is going to move the chain. It's hard enough to move the chain clockwise with the cam gear wrench. Doesn't seem like anything will move with the CAM blocks on.
I took a video but not sure how to post a video. I'll try to figure that out. If anyone has any ideas in the meantime please let me know.
-
got a video on you tube. you can see the vanos gear thing twitch with I apply voltage to it on and off
-
well, didn't make a difference with cam locks off. Same thing. I've taken the whole thing apart again and reinstalled. Same problem. Took the vanos apart to check seals and inside. Those all seem fine.
Perhaps my rig for applying air? Should I not have the oil feed line attach? I have an aftermarket oil pressure guage that tees off that, so mine is a bit different. I was able to get a hose clamp attached to that. Air doesn't leak and does go through even with the kink. Other end just connected to the compressor with 60 psi. I do hear air coming out from somewhere under the exhaust cam gear. I assume oil feeds into the head somewhere in there. But air pressure definitely escapes through there.
-
yeah, this is my bolt going into vanos. I assume I need something that bypasses the oil feed line (that black line?) I was just applying air to the end nipple part with the bolt still screwed in and oil line attached
-
https://www.amazon.com/Vanos-Tool-Banjo-Fitting-113450/dp/B010O1FBLC
This plus an unmolested banjo bolt
-
Hi all, hope everyone is doing well. Not a ton to report on the M3. Got the new trunk on. Looks much better. Not 100% perfect unless you're very close to it and know what to look for. I like it. Small m5 spoiler coming today.
Back to the vanos stuff. Did it a 3rd time, confirmed chain movement was correct with compressed air. All seemed fine. Drove it for a couple weeks with no CEL. Had at least 30-40 different start and stops over the time period, so DME had plenty of time to trip early on but didn't. Then it came on again this week. Ugh, same thing, mixture deviation bank 1, misfire cylinder 5.
So, I did an experiment. I changed coil pack (CP) to cylinder 2 and spark plug (SP) to cylinder 3. Put known working CP and SP from cylinder 2 onto cylinder 5.
Now I get misfire on cylinder 5 and 3 (where the spark plug went) but cylinder 2 is good with the CP off 5. So, I know CP's are fine. (again all CP and SPs are new)
Something appears to be happening on cylinder 5 that messes up the spark plugs. I'm going to try to clear codes and reset DME adaptations, but leave everything where it is. I'll see if they come back as 3 and 5 misfires again. If so I'll move 5 spark plug to another location to see if that follows.
Maybe something with the wiring harness or could be computer related? Ugh.
Would love to get this sorted out. I don't have anyway to live monitor stuff while the engine is running to see if it is truly misfiring or look at other parameters. I think that's the next step.
-
what does the cylinder 5 spark plug look like compared to the others?
I would be interested to see if by chance the o2 sensor connectors for bank 1 and 2 could have been mistakenly switched. I am not sure if wiring lengths and locations would allow that to be possible or not.
-
they all look same to me. I'll take pictures next time I have it out to show you. I'll be gone this weekend putting the vert into storage so won't have time to mess with it till Sunday.
-
Hi all, quick question. I replaced my RTABs this weekend. After I got done I discovered some threads talking about preloading them. I understand the concept and why to do it. Now I just have to figure out the proper way with out the BMW tool. Only it says use a straight edge and measure 8mm above the center of your hub. My questions are:
1. my car is lowered. Should i error slightly more than 8mm?
2. do you measure with the car fully jacked up? won't different cars with different suspensions sag more or less than others, throwing off that 8mm measurement?
3. do you measure for below or above the center of the hub?
I attached some pictures for reference of what I was doing. I was going to measure above center of hub, but still unsure of question #2. I think i tighten it too far off 8mm trying to account for my drop in suspension. I was getting a bad shake this AM from the one side i messed with. Will try to correct tonight.
Thanks for the help for anyone who's done this.
-
yes, stock w/ limiters. i got some tips on bimmerforums:
"Don't fully tighten the bushings bolt.
Install RTAB bracket to car, install wheel, lower car to ground.
Drive the car back/forward 10ft or so so the suspension can settle.
With a marker (pref a paint marker) reach into the RTAB bracket area and draw a line across the bracket relative to the trailing arm.Put the car back in the air, remove RTAB bracket and you should now be able to line the RTAB bracket to the line you just drew. Now tighten and torque the bushing bolt. Tada!"
-
yes, stock w/ limiters. i got some tips on bimmerforums:
"Don't fully tighten the bushings bolt.
Install RTAB bracket to car, install wheel, lower car to ground.
Drive the car back/forward 10ft or so so the suspension can settle.
With a marker (pref a paint marker) reach into the RTAB bracket area and draw a line across the bracket relative to the trailing arm.Put the car back in the air, remove RTAB bracket and you should now be able to line the RTAB bracket to the line you just drew. Now tighten and torque the bushing bolt. Tada!"
Another option that I would guess would work, is to determine just how far you are lowered from stock in the rear. That number is easy to find if you have lowering springs as it should be a published value, less so if you have adjustable suspension. If you've got coilovers, there are published values from BMW for stock ride height from the ground to the wheel arch (or something like that) that you can compare to. If I'm thinking correctly, measure down from the center of the hub by the amount you are lower from stock ,and then up 8mm from that point to set the preload relative to your ride height.
As far as the vibration, unless your alignment is really out of whack, it is most likely that the new RTAB is 'uncovering' and issue elsewhere by transmitting vibrations that were previously being absorbed by the worn bushing.
-
Another option that I would guess would work, is to determine just how far you are lowered from stock in the rear. That number is easy to find if you have lowering springs as it should be a published value, less so if you have adjustable suspension. If you've got coilovers, there are published values from BMW for stock ride height from the ground to the wheel arch (or something like that) that you can compare to. If I'm thinking correctly, measure down from the center of the hub by the amount you are lower from stock ,and then up 8mm from that point to set the preload relative to your ride height.
As far as the vibration, unless your alignment is really out of whack, it is most likely that the new RTAB is 'uncovering' and issue elsewhere by transmitting vibrations that were previously being absorbed by the worn bushing.
note to my idiot self. it usually helps with vibrations to actually tighten lug nuts.............
rtabs all better now.
-
note to my idiot self. it usually helps with vibrations to actually tighten lug nuts.............
rtabs all better now.
At least you caught it before they came all the way off!!
-
-
Morning all, time to pick your brains again. So, I've never been able to figure out my CEL issue and I'm determined. If you'd read back you'd notice car seems to run fine but I'm running rich. Quick summary: I get mixture deviation codes on banks 1 and 2 with negative fuel trims. I'll clear codes and monitor the live data. LTFT starts at zero then works its way to the -8.6% threshold fairly quickly where DME overrides and trips the CEL. I've noticed bank 1 gets there about -1% more quickly than bank 2, but then they both eventually get to the -8.6% I understand this to mean I don't have a vacuum leak as that would cause lean fuel trims (positive) Plus I've tested numerous times with smoke for any intake leaks.
Things I've done within the last 3-8,000 miles: valve cover gasket, vanos seals, fixed intake boot leak, fuel filter, new FPR, all new O2 sensors, sent out injectors for testing (tested good, no leaks), spark plugs, boots, coil packs. Unplug MAF and confirm idle change, so appears to be working. Cam shaft position sensor. The latest was the cam shaft position sensor. Old one was definitely compromised. It had frayed exposed wires. Light stayed off for 2 weeks and a lot of driving so I thought I found it. Then, came back. Same codes.
This brings me to a couple ideas.
1. Possible exhaust leak - I've read if the leak is on the exhaust side before the o2 sensors that can cause rich conditions. I'll be confirming tomorrow if there's a leak at the manifold or elsewhere. Assuming that's ok onto my next ideas.
2. When I got the car it was needing maintenance, valve cover leaked, intake, etc. My thought is perhaps the tune was done with these leaks causing causing misleading lean conditions. Now that I've patched them up, cleaned up fuel filter, fpr, etc it's just flowing that much better and running rich. My question is does anyone here know if you can tune injectors to not run as much fuel? Anyone here know how to for some $?
3. DME compromised? There's a guy on bimmerforums that'll re-flash the tune onto a new DME but that's $380 and i don't want to spend that if it's fine. Car doesn't experience any other symptoms so I assume it's OK?
4. Timing issue from vanos job. I've done it now 3 times checking my work and using the compressed air to confirm movement. Seems OK. But with bank 1 showing signs first maybe intake CAM is still off? Are there computers out there that can sense that? I did job using blocks and all lines up.
5. Coolant temp sensor?
I'm basically out of mechanical ideas to fix / test. Only thing I haven't changed is the CCV. I don't think that would cause a rich condition. I've cleaned out ICV. I was OK replacing all the other parts because they were maintenance items anyway, but now I'm out of things to fix.
Looking forward to hearing all your thoughts and wisdom! Willing to pay money for help. I just don't want to take to the deal because they'll do all the same things I've already done, unless their programs are more capable than what I have.
Thanks, Andrew
PS - detailed and put summer tires on, so you all can blame me if we get 6" of snow Friday night.
-
Never not had a CEL. but i didn't know enough back then to look at fuel trim ratios. was focused on vacuum leak stuff as that is what everyone always talks about. Since I bought from out of state I assume previous owner cleared codes before selling. 1st thing I noticed were 02 sensors were actually disintegrated post CAT. did those 1st but still didn't fix CEL. Then did valve cover as that was leaking oil. Then the rest of the list above as other preventative maintenance along the way. Still haven't pin pointed it. Ordered up a coolant temp sensor for the block as they are only $25 bucks. Figured why not. Will try to put that in tomorrow too, but supercharger might make that a difficult job.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login