Pulled the trigger on electric impacts
-
I didn't know this was such a big issue
It really isn't. Usually it's just a matter of tool size and max torque.
REKIII just has a massive bias against Milwaukee for little reason XDI will say that the IR 3/8" Impact does have quite a lot of torque, though that does appear to come at a cost.
Any difference in body size compared to the Milwaukee m18 equivalent?Edit: was the thread title intended to be amusing?
-
I have an IR pneumatic impact, but my battery impact is a Dewalt which I absolutely love.
-
It really isn't. Usually it's just a matter of tool size and max torque.
REKIII just has a massive bias against Milwaukee for little reason XDI will say that the IR 3/8" Impact does have quite a lot of torque, though that does appear to come at a cost.
Any difference in body size compared to the Milwaukee m18 equivalent?Edit: was the thread title intended to be amusing?
You should see the threads on this in the different facebook group. There is a HUGE issue with it. The pro Milwaukee guys, are violent, belligerent, arrogant, etc. It's really sad, especially since the Milwaukee tools appear to be REALLY nice. Let the tools speak for themselves.
I don't have the IR yet, and when I do, I won't have a milwaukee to compare it too, although I could run down to Neu's to see.
I had an original title that was close to this, then tweaked it a bit to make it funny.
-
That's sad to hear. The one thing I have going for me, is I'm not a shop. I just play in my shed, so even with a 'ticking time bomb' it ticks REALLY slow for me.
There was a few other guys buying the IR's when I did. We'll see if any of them have issues.
Next up, hopefully a tool chest. Really looking at the deeper Snap-On or Matco. Seems the off brands (which would be fine for me) are 25" deep max, I'm looking for something closer to 30.
What width are you looking at?
-
You should see the threads on this in the different facebook group. There is a HUGE issue with it. The pro Milwaukee guys, are violent, belligerent, arrogant, etc. It's really sad, especially since the Milwaukee tools appear to be REALLY nice. Let the tools speak for themselves.
No kidding. I don't know how you could get arrogant about it. If reliability was poor on some other tools that would be a bit more opinionated than just numbers, but even at that it's no real reason to get angry about.
Numbers sold me my M18 Fuel 3/8", and that's what should sell most people on tools. Le numericals -
Facebook groups for tool enthusiasts are a thing now too?
-
Facebook groups for tool enthusiasts are a thing now too?
-
^tapatalk double posting can suck my ass
-
Facebook groups for tool enthusiasts are a thing now too?
hey, hookers are people too.
Dan
-
What width are you looking at?
Depends....60-ish. I'm a little open right now. A friend had a macsimizer that I used all the time, trying to get him to tell me the width so I have a basis of comparison.
-
Depends....60-ish. I'm a little open right now. A friend had a macsimizer that I used all the time, trying to get him to tell me the width so I have a basis of comparison.
Check out Waterloo. They have a 56" that's 30" deep. Most products are madr in the USA with comparable quality to snap on or mack at a cheaper price. I've had Snap-On boxes and when I got out of the shop I traded my last one for a harbor freight box plus cash that was slightly smaller. It holds tools just like a toolbox should.
-
This is my favorite completely irrelevant ad. The drawer slides could be made of brick for all you know.
How does this show that it is a good toolbox?
-
Because marketing
-
I've seen that ad, quite impressive!!!
From what standpoint does this impress you? As a feat of strength, or as a toolbox?
-
From what standpoint does this impress you? As a feat of strength, or as a toolbox?
Uhmmm, that's a deep question. Lot's of things about it impress me. The toolboxes holding the weight, especially the casters is impressive. The fact they got a dump truck up on there is impressive.
Am I missing something? Am I not to be impressed? Is a dump truck sitting on toolboxes a common thing?
-
I've seen that ad, quite impressive!!!
I will look into waterloo, who sells them?
You can find them at Fastenal. We sell them to our technicians at work through a special order program we set up at a discounted price but not to the public.
-
My favorite part of this whole conversation is you continue to point out the douche bag owners of these other products and their stupid whiny groups but you own a Raptor and a BMW... both groups considered to be douchey and whiny.
-
Uhmmm, that's a deep question. Lot's of things about it impress me. The toolboxes holding the weight, especially the casters is impressive. The fact they got a dump truck up on there is impressive.
Am I missing something? Am I not to be impressed? Is a dump truck sitting on toolboxes a common thing?
Looks like an acceptable weight for a 3 axle dump truck that is empty is 24,000 lbs. We see that it is resting on 6 toolboxes with 4 casters per.
24,000 / (6x4) = 1000 lb / caster
This isn't any crazy load for a commercially available caster, and even if you jump up to a 15 ton truck you're only looking at 1250 lb per caster.When are you ever putting that much weight on the top of the toolbox? Why design it for something that it will likely never do?
To me that ad says nothing about the usability of that box, just that you can put a lot of weight on top of it.
As stated before, I like picking brains.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login