It's like the Same but Different: My 528e build
-
whats with the wood in the trunk?
Rare OEM Sub box
-
what about the plank?
That's actually a stack of crusty floor mats lol
-
-
Chris ... I have got some stuff on your list. I will be at my shop tomorrow night if you want come take a look see
Sorry I missed this! Gotta wait until pay day tomorrow anyways. Shoot me a text/pm next time your available.
-
I just bought myself an e28 parts car going to pick her up tomorrow I have all the stuff to do the 5 speed swap to mine and ill have leather and the better steering wheel... ODB will ride again and Im using the parts car to do the Frankenstein 240sx coilover e30ix setup but gonna cut the stock springs for now
1984 BMW 528e - SETA and manual swapped! M50 to come!!!
1988 BMW 528e - Need parts?
1991 Chevy C1500 (mighty 350 with TBI and Wisconsin weight reduction package)
1996 Mazda Miata (SOLD!!!)
1996 BMW 325i (Donor car)
1998 Chevrolet Corvette (BEAST)
2001 Jeep Grand Cherokee (BROKEN)
-
I just bought myself an e28 parts car going to pick her up tomorrow I have all the stuff to do the 5 speed swap to mine and ill have leather and the better steering wheel... ODB will ride again and Im using the parts car to do the Frankenstein 240sx coilover e30ix setup but gonna cut the stock springs for now
Do tell me about this coilover setup, I've eard of the IX struts/springs in the fronts, but nothing of 240 struts/springs in the rear.
-
Do tell me about this coilover setup, I've eard of the IX struts/springs in the fronts, but nothing of 240 struts/springs in the rear.
1984 BMW 528e - SETA and manual swapped! M50 to come!!!
1988 BMW 528e - Need parts?
1991 Chevy C1500 (mighty 350 with TBI and Wisconsin weight reduction package)
1996 Mazda Miata (SOLD!!!)
1996 BMW 325i (Donor car)
1998 Chevrolet Corvette (BEAST)
2001 Jeep Grand Cherokee (BROKEN)
-
Small Update
Progress hasn't been going as fast as I wanted it to, but it never works out that way! I've been mainly spending my time parting out the old car so I can just get it out of the garage. Last week I did load some interior parts up into the truck and took them over to work to store in the car. I did a little clean up and got all the carpet installed in the trunk. I also cleaned up the rear shelf and speaker pods. That's the extent of my work so far on the new body
.During Clean Up
After, Carpet will need to be dyed.
Towing her back out after the first wash.
Tonight I was working in the garage trying to get the transmission off of the old motor and one of the bolts stripped.
#$%9^#!!!! I was out of cut off discs for my dremel so I will need to get some more to finish cutting off the bolt head tomorrow night. Hopefully that will be relatively easy and I can finally get the transmission in the new car. It's kind of a slim chance at this point I'll have the car running for the meet Sunday but I can still try 
-
updates!
nice!
also, I spy rampelsausage.
If you need someone to stand around and make wild accusations about random things. lemme know. I'm in.
-
This dude made mincemeat out of the stripped inverted torx bellhousing bolt on my trans. It was the top bolt so i had to pull the engine + trans from the car to get to it but if its in your parts car you could sawzall an access panel through the driveshaft tunnel (or maybe from the shift lever area) and work at it from the comfort of your drivers seat.
Simply find the best fit, smack it on with a hammer, remove it with ease with a ratchet. Took a whole 30 seconds vs. 10000 seconds of being angry without it.
-
This dude made mincemeat out of the stripped inverted torx bellhousing bolt on my trans. It was the top bolt so i had to pull the engine + trans from the car to get to it but if its in your parts car you could sawzall an access panel through the driveshaft tunnel (or maybe from the shift lever area) and work at it from the comfort of your drivers seat.
Simply find the best fit, smack it on with a hammer, remove it with ease with a ratchet. Took a whole 30 seconds vs. 10000 seconds of being angry without it.
I second that, I have a set of these and they have made quick work of some very round bolts
-
This dude made mincemeat out of the stripped inverted torx bellhousing bolt on my trans. It was the top bolt so i had to pull the engine + trans from the car to get to it but if its in your parts car you could sawzall an access panel through the driveshaft tunnel (or maybe from the shift lever area) and work at it from the comfort of your drivers seat.
Simply find the best fit, smack it on with a hammer, remove it with ease with a ratchet. Took a whole 30 seconds vs. 10000 seconds of being angry without it.
I'll see if they have a smaller sized set or if I could borrow one from work. Its the 8mm 6 point star bolt on the bottom of the bell housing. Since the engine/trans is out of the car I already started cutting through the bolt head though.
-
Got the transmission off!! Feels good to finally wrestle that baby out of the garage. I also got all the clutch parts except one hard line I'll have to grab tomorrow night but for the most part the 5spd "re-swap" will be completed tomorrow night.
Its about time!
Ghetto ring gear holder, did the job!
-
yay! there better be an admin,
in a bmw (not a suburban)
at the meet this weekend!!
Trans didn't get in tonight cause I forgot a gasket at home Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login