SCHLEPN | The E39 540itA Story
-
Had a little window from 10-12.
-Mounted up the oil filter housing & PS reservoir mounting bracket.
-Installed all heater core coolant hoses, fuel pressure regulator vacuum line, brake booster vacuum line.
-Installed driver's side intake.
-Popped in new air filters.
@DrLeadFoot
-
Another little window today. Popped in the radiator, new expansion tank, fan and a new OEM PS pressure line.
Last night Mike got the pedal assembly in. Just need to get the gas pedal mounted up.
@DrLeadFoot
-
Mike chipped away a bit! I watched the bucks game. 🤩
Gas pedal in and 1 of 2 M5 side mirrors installed!
@DrLeadFoot
-
-Driveshaft in
-Diff oil in
-Clutch lines all buttoned up
-Passenger side headers bolted up
-Crank sensor installed
It is ready for all fluids and wiring is next!
@DrLeadFoot
-
Sport button is wired up from the dash to the DME. Hijacked some steptronic wires for this. Blue & grey and blue & yellow wires. Swapped pins and we should be good!
Fuel leak diagnostic and Brake light test switch are wired up.
Hopefully we will get the rest of the wiring done tonight!
@DrLeadFoot
-
Got the topside wired up, sport button and servtronic!
Need to pop in new style fuel pump relay. Have run a ground wire to it and move a pin on the 540i female side of connector and the new style relay will be good to go.
Pin 2 wires behind the cluster. One to the DME for reverse lights and the other to the clutch switch.
Changed the trans fluid. Added oil. 10w60 liqui moly.
Need to top off coolant, power steering fluid and bleed brakes/clutch.
Getting close!!
@DrLeadFoot
-
Finished up the cruise control, clutch interlock and M5 fuel pump relay wiring. Mike added a proper ground for the fuel relay.
Pulled the fuel relay and cranked it over a couple times to prime the oil. Popped the relay back in and fired it up on the first try!
Bled the clutch and brakes. Brakes felt great until we hit the gas a spun the rear wheels then the pedal went to the floor. We think it has something to do with the DSC pump not being bled properly.
Started buttoning up the interior and finished the cabin filters and new M5 rear wire harness covers.
So close to being done!!
Attachments:
@DrLeadFoot
-
Yesssss
-
Hey look its Bill! Will the 540i exhaust bolt up or are the downpipes bigger on the S62?
That's Bill! He came over to Mike's twice to kick it and help out a bit! Between Mike and Bill there is a lot of knowledge in that garage!
@DrLeadFoot
-
I'm going to have Structure Fabrication and Design do the exhaust. Thinking 2 mufflers and high flow cats or 3 mufflers. Need something mild for family road trips!
@DrLeadFoot
-
Just for ideas these are the phases we've gone through on my brother's 540i's.
Phase 1: Dinan Muffler (stock but gutted) sounded more or less stock.
Phase 2: Cut off the Dinan Muffler. Sounded great, loud enough at idle but perfect for cruising. About 1/2 throttle it was just right and no drones at all. Just the cats and resonators
Phase 3: No resonators, straight pipes. Sounded like a tractor and it droned. Absurdly loud at WOT lol.
Phase 4: Full Super Sprint catback w/ resonator and muffler. Slightly louder than stock but not by much. Opens up a little more WOT.
Phase 5: trying to go back to phase 2. Either unbolting the muffler and replacing or gutting the cats.
TLDR I'd recommend performance resonators somewhere. 3 Muffflers might be overkill. Electric cut outs would enable best of both worlds too.
-
Dude, you guys absolutely hammered through this. I love your evil laughter in the videos!!
I vote high flow cats and dual resonators. If that's too loud then delete the resonators and run high flow mufflers. As long as the tips go out past the rear bumper and dont turn down, it wont be as loud in the cabin.
Chubs has built some nice exhaust set ups, im sure you will figure out the best option.
https://www.instagram.com/_jdesigner_/ http://nevertoolow.tumblr.com/
🥳SOLD BMW E24 633CSI - BMW M30B32 🧪SOLD HCH ES9 - 1.3 LDA
👽BMW E30 325IC - Toyota 1JZ-GTE ⏰ HONDA EF9 CIVIC SI - JDM B18C5
☠️BMW E36 318i - Ford 5.0 FE302 🚴♂️ GT-Labomba - 26x2.75 Freeride
🤹♀️SOLD BMW E36/7 Z3 - BMW M54B25 🧓SOLD BMW E10 2002 - BMW M10M05 -
Took it for a little test drive yesterday afternoon after bleeding the brakes again while activating the ABS/DSC pumps. It stops!!
While on test drive I took the dirty girl through the car wash! It feels good to see this outside!
Last night, we popped in the M5 fuel pump. Had to swap over the 540i top to keep the barbed fitting as the M5 has a quick disconnect.
Swapped the mirror motor pins on the driver's side so pin 1 has the blue wire and pin 2 has the white wire so both door modules matched pin locations. This corrected the mirrors folding opposite ways when you hit the button.
Bled the clutch again, The feel is still not 100% but it drives.
Felt it was time to add the fresh M badge on the motor!
Counting down the days to the exhaust shop!
@DrLeadFoot
-
Dude, you guys absolutely hammered through this. I love your evil laughter in the videos!!
I vote high flow cats and dual resonators. If that's too loud then delete the resonators and run high flow mufflers. As long as the tips go out past the rear bumper and dont turn down, it wont be as loud in the cabin.
Chubs has built some nice exhaust set ups, im sure you will figure out the best option.
Family road trip car so I want it pretty stealthy. Excited to get a gameplan in place and get this DONE!
@DrLeadFoot
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login