Alpine White Zender Kit E24 633CSI

[P_Roloff]

I love the interior, those sills are pretty different!

And I really like those RS’s stepped, I’d say go for it. I’d imagine that they’d sell for a lot more if you ever got rid of them if they were stepped and cleaned up a bit.

[m42b32]

I actually really like the 16's, with the right stance and some meaty tires they could look awesome

[YoungCR]

Agreed on the 16"s

[jc43089]

16" is the way to go.  Too big doesn't look quite right on old cars in my opinion.

[Earl]

I don't mind 18's on e24's but 17's are the perfect size to me. 16's just always look a hair small and oddly they look smaller when you lower the car. 

17's for comparison to above=)

[Earl]

The massive slant lips don't help make the 18's look any smaller. These Kinesis are 18's but don't quite look as large.

[Earl]

Might as well throw in a picture of how small 16's look too. Ignore the miles of wheel gap lol

[straight6pwr]

so i'm thinking m70 twin turbo would fit nicely under the hood.

[Jdesign]

Those tires are soooo small on the 16's @Earl LOLOLOL

Im picking up the set of 17 style 5's tonight so I will be right in between.

straight6pwr said:

so i'm thinking m70 twin turbo would fit nicely under the hood.

You stop that. 

But I like your idea......

https://bmwconceptsarchive.wordpress.com/2015/01/11/bmw-6-series-v12-mule-e24-1987/

But for consistency sake, I would probably put something non-BMW in there.

[Daggerty]

That steering wheel looks oddly similar to an 80s bikini bottom.

[Jdesign]

Daggerty said:

That steering wheel looks oddly similar to an 80s bikini bottom. 

I mean, thats not a bad place to look for inspiration is it?

[Jdesign]

Picked up the Style 5's this weekend and test fit them. The tires are way too small and completely destroyed. I plan on refinishing them while the RS's stay on the car. Then once they are refinished I will swap them out and refinish the RS's

I also ordered the last of the front suspension parts last week from FCP and went to install them this weekend.

I got everything apart, go the new control arms in, but noticed the Tie rods were slightly different.... Yup totally an inch too long on either side. I assume its e12 stuff and I will be contacting FCP today to get that situated. Ughhh SO close

I also ordered exhaust piping for replacing the muffler that was rotted out, that has yet to show up so I haven't been able to cross that off quite yet. 

Parts to order / find

• Tie rods   (DAMMITTT)
• Steering Arm
• Trailing Arms
• Suspension Control Arm and Ball Joint 
• Ball joints
• Front valanc
• Shift Bushing
• Muffler/ rear exhaust
• Front springs
• Speakers (4 minimum)
• Wipers
• Tail light surrounds (might need to make my own)
• Interior dash blanks      @YoungCR  -might have these?
• fog lights   
• Door light switch
• Right rear window switch (in the rear of the car)     @YoungCR  -and might have this?
• Battery tie down     @YoungCR  -and might have one of these? I broke the one I got from @m42b32  

Labor

• Remove tint
• Muffler/ rear exhaust
• Install v belts
• Adjust steering box
• Extreme interior detail/ buffing session
• New brake pads / Rebuild caliper
• Turn signal Relay needs to be cleaned or replaced

[Earl]

You should add some 50mm spacers to that list too

[Jdesign]

Earl said:

You should add some 50mm spacers to that list too

I know!!! I haven't yet because I might just have some in a box.....

[Jdesign]

I know @m42b32 It was sad. I had a battery in there, and I needed it for another car I bought, and when I removed it, the long bolt snapped halfway out. Really annoying because now I have to figure out a new means of securing the battery.

[jc43089]

Bungee time, Git-R-Dun

[m42b32]

Jdesign said:

I know @m42b32 It was sad. I had a battery in there, and I needed it for another car I bought, and when I removed it, the long bolt snapped halfway out. Really annoying because now I have to figure out a new means of securing the battery. 

I get a little scared every time I need to take one of those out, its such a long/thin bolt!

[Jdesign]

m42b32 said:

I get a little scared every time I need to take one of those out, its such a long/thin bolt!

Exactly. And I was in a hurry and didn't think about it

[Jdesign]

Exhaust piping came in. $26 shipped for 7.5' of mild steel seemed like a really cheap price. This will be the replacement for the muffler that was completely destroyed. Surprisingly the car isnt ungodly loud without a muffler so I figured this would help to wake it up a little.

Still waiting on the correct steering components to get here so I can finish that up.

[Daggerty]

Jdesign said:

Exhaust piping came in. $26 shipped for 7.5' of mild steel seemed like a really cheap price. This will be the replacement for the muffler that was completely destroyed. Surprisingly the car isnt ungodly loud without a muffler so I figured this would help to wake it up a little.

Still waiting on the correct steering components to get here so I can finish that up.  

Is it galvanized? Kinda hard to tell