Lifted E30 V2

Jdesign

Do I even want to know what thats about? LOL

HipMF

^^^ All you need to know. Ice races MR2s and thinks he's a badass cause he's faster than a FWD Impala.

B C

Understandable point of pride. Impalas go faster when they dont have all that pesky coolant to haul around and pump

GunMetalGrey

I want to lower the front subframe a good bit (1" or more) but am sitting here debating what to do about the control arm bushing brackets, do I bring those down with? I don't enjoy the idea of that too much as their positioning is key to other geometry things, but I don't know if leaving them in the stock spot would be a good idea either...
Opinions?
Pic for reference (looks like they modified theirs to accept the e46 bushings)

In attempt to not disappoint

GunMetalGrey

I finally have a fully functional blower motor! Replaced the resistor for it last night and now I have all fan speeds!

Got a cheap intercooler

Tried to track down my coolant leak, but I had waited too long so everything appeared to be dry. Judging by where it had drained I am kind of wondering if the heater core itself is leaking. Going to spend a bit more time on that one.

I had been getting a fair bit of oil leaking when parked, from weird areas, and yesterday realized why.
The crankcase vent has some sort of oil separator and I underestimated how much oil that would move. The stock setup has the oil drain line going into the oil pan below oil level, and I think I'm going to take that hose and feed it into the dipstick tube (add a tube) or see if there is somewhere on the e30 pan I can plumb it into.

Large hose feeds over to the air filter as there is plenty of smoke that comes off that.

I don't know if this has been seen in any of my pictures before. It's an Factory Five cobra rep. It's been amusing watching it go from a bare frame to where it is now.

jc43089

That Cobra looks fun!

stealthbimmer

Get that cobra out on the ice and see what she can do.

Jdesign

That Cobra is cool. IDK if that would be my choice if I was going to build a F5 car, but all those kits are sweet no matter what they are. Its so temping too as you can build one for roughly$10K starting.

I was able to clean that fan switch on my car. But I am cheap so im sure it will fail again.

GunMetalGrey

I'm leaking fluids like they are going out of style.....

It looks like the heater core is leaking, and it is leaking enough to drain the expansion tank in a day or two. Gotta replace that.

I increased the fuel amount, and now the low pressure return on injector 6 is leaking a lot more than before. Gotta fix that.

I'm leaking oil out of the crankcase breather/separator. Gonna tap the return from that into the pan (like OE setup)

Adding more fuel was very amusing. Simple turn of a screw and now it is substantially faster. It also makes me want a different/new/bigger turbo knowing that the current one has compressor wheel wear and is likely less efficient than it should be.
I took it out for a hot second last night, and I have more torque than traction down low, which is kind of a fun problem to have.

Jdesign

GunMetalGrey said:

I'm leaking fluids like they are going out of style.....

It looks like the heater core is leaking, and it is leaking enough to drain the expansion tank in a day or two. Gotta replace that.

I increased the fuel amount, and now the low pressure return on injector 6 is leaking a lot more than before. Gotta fix that.

I'm leaking oil out of the crankcase breather/separator. Gonna tap the return from that into the pan (like OE setup)

Adding more fuel was very amusing. Simple turn of a screw and now it is substantially faster. It also makes me want a different/new/bigger turbo knowing that the current one has compressor wheel wear and is likely less efficient than it should be.
I took it out for a hot second last night, and I have more torque than traction down low, which is kind of a fun problem to have.

I wish it was always that easy.

GunMetalGrey

Tried removing the #6 injector.
27mm deep 1/2 drive with a 2.5 foot breaker bar.
I got concerned as to what was going to give due to the amount of force I was applying, and nothing was moving.

Yay stuck things!

straight6pwr

those oversized vintage-styled wheels on the cobra are fricken amazing.

YoungCR

GunMetalGrey said:

Tried removing the #6 injector.
27mm deep 1/2 drive with a 2.5 foot breaker bar.
I got concerned as to what was going to give due to the amount of force I was applying, and nothing was moving.

Yay stuck things!

Soaked with PB blaster for a few days? The injectors on my truck take a 30mm socket and had a 3ft pipe on a 1/2in Craftsman breaker bar and it still took force to break 'em all loose.

Daggerty

Try to take it out when the engine is at operating temp.

HipMF

Try to temp it when the engine is operating at take out.

GunMetalGrey

YoungCR said:

Soaked with PB blaster for a few days? The injectors on my truck take a 30mm socket and had a 3ft pipe on a 1/2in Craftsman breaker bar and it still took force to break 'em all loose.

Yeah I hit it with PB. Steel injector bodies in an aluminum head, should be a fun one.

Daggerty said:

Try to take it out when the engine is at operating temp.

Yeah that may be my next attempt.

HipMF said:

Try to temp it when the engine is operating at take out.

I wish I would have thought of that before

B C

It takes a while to realize the possibilities you have once you own a temp gun

GunMetalGrey

Snap said:

It takes a while to realize the possibilities you have once you own a temp gun

But does it?

GunMetalGrey

I had my wheaties for breakfast yesterday.

I really leaned on the breaker bar and it turned about 1/8th of a turn and then got super tight. I rocked it back and forth then pressed on. Eventually it got to the point where I could unscrew the injector by hand.
Caked full of crap, it came out.

What the low pressure return should look like

What the low pressure return did look like

Now to find a "new" injector, or at least the back half.
I took it apart for fun.

Now I need to figure out how/why this engine is leaking so much oil/fluid. This is nuts...

GunMetalGrey

Super low RPM "pull" that I forgot to post. This was after turning up the fuel amount, and before adjusting the low boost fuel, smoke that black is going to drive my EGT's up too high! But it looks cool, and that's what it's all about right?

WIBIMMERS

Lifted E30 V2