Build Thread?
-
What are you gentlemen running for sway bars? I ran ST's in my 318 and was happy with them, but curious what others run.
I went to an auto-x event yesterday, and was not thrilled with the way the car performed. I was running very slow times, and the tires didn't sound happy most of the day. I can see plenty of body roll through corners and through the slaloms and am thinking upgraded sway bars would help snug things up a bit. I am currently on stock sway bars.
The event was fun, my gearing is not. Running a 2.93 resulted in being out of the power band most of the time, yet we were cruising down the highway at 3200+ rpm on the way home. -
Feel free to critique, yes my hands are all over the wheel, I need a tighter ratio rack....
-
I ran stock sways for my first auto x and blew the mounts of the subframe. I have yet to drive the car but I installed 22/19 ST with adjustable endlinks
-
Long time no update!
New clutch master ordered, old one wasn't doing too well. Never go with used parts when doing a manual swap!
New tires put on (Dunlop Direzza ZII's) to replace the 4k mile BFG's (one gouged tire, wouldn't hold well in corners)
Lots of WOT...... like, a LOT.
Got tim's e30 running, it is many times faster than mine.
Drove with Collin.
Picture dump time. Just kidding, things are being weird. This will have to do for now.
-
Post
-
Post
This is the only reason I come to this site, for quality content like this.
-
This is the only reason I come to this site, for quality content like this.
I'm glad that I can make your day!
I have starting working on a little compilation of videos that shall be posted soon, don't you worry. -
I'm glad that I can make your day!
I have starting working on a little compilation of videos that shall be posted soon, don't you worry.Based on this threads timeline, I'll check back in October 2017
-
The M52 e30 had a clutch slave cylinder that was leaking like a pig, and so like any reasonable vintage BMW owner I spent about 2.5 weeks waiting to buy the part, and then finally put the new slave in last night.
The Good News:
The clutch pedal is much more firm
It finally engages at a logical point!
It was shiny and newThe Bad News:
Swapping slave cylinders on a ZF in an E30 is a pain
I didn't even drive the car after swapping it.I am looking forward to boosting the engine again this winter, as everything has been going really well with it thus far in terms of motor break in and such. The car feels good, but could use an additional 250hp no problem!
-
-
Haha awesome!!!!
Sent from my SM-G930R4 using Tapatalk
-
I didnt post the other two yet, I shall
Sent from my XT1080 using Tapatalk
-
Update:
Though I don't have cool videos like some other people here do, I raced an e36 M3 on the highway yesterday evening. I rolled up on him and noticed it was quite clean, lowered, nice wheels and collector plate on the back. He didn't notice me until I downshifted to go around a truck after I realized I was in the wrong lane. I noticed he quickly swept a couple of lanes of traffic and was right behind me. Obviously being the responsible citizen that I am I matted the gas and we went up to about 130, where I just kept inching further away from him. He had his windows up, I didn't, so I'm sure that was a big factor
I found a lot of round-abouts and also probably annoyed a lot of people in the process.
This thing is fun to drive, but boost again will be even more fun! -
where's the part with you bouncing over the roots in the mud?
that shit was hilarious 
Even if you did have cool videos you wouldn't post them...
-
-
-
I will be bringing the E back into the shop today/tomorrow and getting back to work on it.
Things to repair:
Oil Pan replacement
Rear Brake (parking brake grenaded?)
New rear brake lines (through the cabin/trans tunnel)
Re-Work the skid plateI am going to be putting e46 control arms on the front of it, which will increase the track width more, and I currently barely clear the fender flares, so I will be widening the fenders for it. I look forward to seeing how that turns out, and deciding on how I truly want to go about it.
That being said, I could use a spare fender (DS) as the fender flare was pulled in an odd manor that may not clean up well.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login